Jump to content
SAU Community

Recommended Posts

Hey guys,

I have a series 2 R33 GTST that is annoying me..

Its 99% standard, just had all 4 discs machined and all 4 corners had new brake pads.

I drove the car for about 1000kms and it ran perfectly, then out of nowhere it started pulling hard to the left.

I had it checked out by a mechanic and discovered my caster bushes were buggered, so I had them replaced and got a four wheel alignment done. The car still pulls to the left just as bad.the person that did the wheel alignment said it might have a bent strutt.

I doubted this as the car started pulling out of nowhere on the freeway without hitting anything.

When braking real hard the car is perfectly straight and pulls up perfectly, but once the brakes are let off it will pull to the left again.

Any ideas or common faults? I was thinking a brake might not be fully releasing?

Please post any ideas :)

Link to comment
https://www.sau.com.au/forums/topic/406528-pulling-to-the-left-help/
Share on other sites

OK, so obvious causes are tie rod ends, rack ends, and ball joints. Any one of these (if badly worn or damaged) can sit nicely in a given position whilst being wheel aligned, then shift to another position once the car is under way and has dynamic loads on the suspension. The same can be true of upper and lower control arm bushes.

It may also be at the back. If you have a stuffed HICAS tie rod end it will steer the car, although that usually doesn't feel like the front end pushing so much as just being strangely unstraight driving.

It also could have been a shit alignment initially.

Unfortunately for a simple thing, it often is done incorrectly. I've had some shocking alignments over years from reputable places even after I've told them what spec to align to;

1. They think they know better and don't do what you ask

2. Their equipment isn't calibrated correctly so it might be right on "paper", but the car is actually out.

You can tell the car isn't "right" by just driving 500m down the street. So that is also something else to consider as well.

Did you replace your caster bushes with adjustable items?

What are your wheel alignment specs?

Are your tyres directional and if not have you done a left to right swap?

Thanks for your ideas guys, you all raised valid points.. Tyre pressures all good, not sure on alignment specs, just standard I guess.

Non adjustable caster bushes fitted.

I have booked it into a different mechanic next week, so il be sure to update you after that.

Thanks again

It MIGHT also be the set-up itself

0 toe with equal caster (left/right) and lower offset wheels will also feel like it is pulling left pretty hard on our cambered roads.

ie. A 0 toe car with equal caster and flush wheel will follow the grooves in the road VERY closely. If you let the wheel go on almost any slightly cambered road will cause a obvious steer to the side of the road.

Normally the caster is split left/right to compensate somewhat.

Obviously this doesn't explain the sudden onset. For that I am thinking tyre wear.

Edited by simpletool

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah pretty impressive hey, good to see quality products not over-shooting their prices. That's what drew me to buy the hypergear turbo, just a shame I've never got the chance to see it in action
    • Thank you GTSBoy and MBS206 I have done the compression test with the motor out of the vehicle, reason for the test was to see if I needed to remove the head and do rings etc while its out. I'm in the process of respraying the vehicle and tidying up a few things. Story behind it all is I've just purchased the skyline and it was running when I got it, never drove it on the street though as I wanted to pull it down and do it all up again before registering it. the gentleman I purchased it from told me the motor has a forged bottom end and has a decent tune through it but I was going to pull the sump off anyway to see if it is a forged bottom end. that's why I thought id do a compression test beforehand. 
    • Man, I'm kind of amazed that the price of the turbo has not changed in 7 years. Everything else is inflating beyond reason, but not this? Good on Tao / hypergear I guess? Anyways, good luck with the sale!
    • I'm selling my brand new, in the box, never used Hypergear ATR45 - and I had some additions I paid for a few yrs back when I purchased it. Never ended up having the rest of the money to add all the mods at once, so I just ended up slowly selling each part. I originally had it internally gated, with the dump pipe, however I found it was incompatible with what I was going to use it for, so I contacted (I think Ken) from Hypergear, and he and I messaged back and forth & he got me to ship the turbo back, where they modified it & made it externally gated, and gave me the 5 bolt dump pipe attachment for custom welding. (Photos below) This turbo like I said has never touched the inside of an engine bay, it's completely brand new, never used, been sitting in the same box it arrived in, covered in plastic & all. Below are the photos of it: And while the guys at Hypergear were making it in-shop, they sent me some photos of the process: I'm looking at selling this just because I'm in need of the money right now, and don't have plans on modifying the 34 anytime soon - and from reviews & peformance sheets, this turbo had amazing results back when I was researching. The turbo was purchased in 2018 for $1.9k, with the mods I got added on. Looking at the website now, for the same turbo they sell (ATR45SAT), with the current addons it adds up to $1830 for the turbo Current addons included: - Bolted dump adaptor - Ball bearing CHRA - Braided oil feeding line So I'm looking to possibly sell it for around $1800, with shipping included in that 1.8k, It cost me around $120 to ship - so yeah thought I'd throw it out there and see if anyone was interested in purchasing. Cheers!
×
×
  • Create New...