Jump to content
SAU Community

Shout Out To Scotty Nm35 - I Have Boost Again!

ドッミ

By ドッミ,
in Four Door Family & Wagoneers

 Share

Recommended Posts

ドッミ Newbie

ドッミ

Posted
Posted

A big shout out to Scotty NM35 for all his help and skinned knuckles with the removal and install of my turbo!

New shorter core produced quite a few install issues and problems for Scott along the way. But he endured and I have boost again!

Coupled with a 'Scott Dump Pipe' and actuator mod, there is a definite extra kick.

Thanks so much Scott. Love your work.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

No problem Dominic, glad to help. Did you get underneath and check it out?

Not very happy with the way this turbo was installed, too many mods required to make it a feasible option. That said the stock like response felt good for an untuned engine.

You are lucky I waived the bandaid tax, costs could have blown right out. :)

Sunkist Grand Master

Sunkist

Posted
Posted

Welcome Dominic

Yeah, I hear Scotty does OK work :)

What turbo did you get?

Cheers, Leon.

Lol ok? There were SOOO many problems Scott had to fix after getting the turbo back.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

iamhe77 Grand Master

iamhe77

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

Sounds like the same issue that Craig had when his 3071 highflow went on.

Sunkist Grand Master

Sunkist

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

Pick up yo phonnnneee nigggahh

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Sounds like the same issue that Craig had when his 3071 highflow went on.

Exactly, even though I was promised it would fit as he had already sold two of them. It's easy to fit when someone else is doing the work though.

ドッミ Newbie

ドッミ

Posted
  • Author
Posted

No problem Dominic, glad to help. Did you get underneath and check it out?

Not very happy with the way this turbo was installed, too many mods required to make it a feasible option. That said the stock like response felt good for an untuned engine.

You are lucky I waived the bandaid tax, costs could have blown right out. :)

Haven't had a chance to climb under and look as yet... Got home from work in the dark yesterday, then back here this morning in the dark! Things one has to do to pay for repairs to a shagged M35 turbo!

Really impressed by the acceleration. As you said, close to stock. Very linear and coming on from approx 2500rpm with the extra kick.

My original post certainly didn't describe just how much stuffing about you had to do. Word of warning for anyone else going down this path... Speak to Scott and he will say, DON'T, I am sure.

Thanks for waiving the bandaid tax - with the number of cuts suffered, the cost would easily been higher than the value of the car!!

That was a mighty big look of relief in the rear view mirror, when I drove off - clearly happy to see my car disappear!

Sunkist Grand Master

Sunkist

Posted
Posted

That was a mighty big look of relief in the rear view mirror, when I drove off - clearly happy to see my car disappear!

relief?

hahah he was probably pissed off that he had to start mine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • aneesr34
      Stock Airbox and Snorkle for RWC - VIC west

      By aneesr34 · Posted

      Thanks mate, couldn't find in VIC, ended up ordering one from NSW, getting rwc to get new plates and registration done.
    • Dose Pipe Sutututu
      EFR7670 exhaust housing selection RB26

      By Dose Pipe Sutututu · Posted

      Before all the EFR fan boys come in, have a look at: https://www.garrettmotion.com/racing-and-performance/performance-catalog/turbo/g-series-ii-g30-825-58mm/ It also comes in a T4 1.06 divided housing. I would dare say if you want response & also decent power, this thing would chop.   AND apologies, just re-read your post, you've already bought the turbo... whatever you do, make sure you stick with divided housing and proper twin scroll manifold.
    • GTSBoy
      EFR7670 exhaust housing selection RB26

      By GTSBoy · Posted

      People have got to stop doing that. ShatGPT is not a search engine. It is a hallucination factory.   I also would recommend the 1.05. The .83 will "work" for you , in that it will be more responsive, but I think you'll find that it won't be anywhere near as good running it out to 8000rpm as the big housing will be.
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Decided for the first time ever I would tow my car TO the track day on the same working theory as bringing tools and spares "if I have it I wont need it, but if I leave it behind i will 100% need it" all setup and ready to go out and try these A050 for the first time First session showed I needed to stiffen up the dampers a touch but still managed a few 1:21's without much effort. things were looking good. Came in a dropped the tyres down  to 26/28 as they had gotten to 35/33C from 22C cold The first lap of session two I managed to drop into 1:20's. Then in the second lap into the second session. Coming into T3 and I suddenly lost brake pedal followed by some huge rear end vibrations and scraping sounds. Got it back into the pits after session ended and found this. in the attached video, all of the wobble is in the hub its self, wheel is mint, and bearing feels tight. lKXLqpd - Imgur.mp4   Deciding it was a bent spindle I tried to find bearing/hub assembly locally but was unsuccessful so it was loaded back onto the trailer i luckily brought it on to drag it back home  
    • r32-25t
      EFR7670 exhaust housing selection RB26

      By r32-25t · Posted

      1.05 you’ve gotta let it breath 
×
×
  • Create New...