Jump to content
SAU Community

Fule Pump Upgrade

hnr32-25T

By hnr32-25T,
in Engines & Forced Induction

 Share

Recommended Posts

hnr32-25T Apprentice

hnr32-25T

Posted
  • Author
Posted (edited)

just purchased a walbro intank good for 500hp, pretty sure its plug and play, just need to hold it in with a cable tie apparently. jeez

Cheap Walbro GS3442 does it for me- just do the direct 12V rewire.

why hard wire it?

Edited by hnr32-25T
battery Mentor

battery

Posted
Posted

why hard wire it?

These bigger pumps pull a lot more amps, not sure what the stock fuse size is but a pump like the walbro 400/416 can pull over 20 amps which is way more than the stock wiring will cope with.

I wired a 416 up the other day (used 6mm to/from relay and 2.5mm in tank) then to test I used a bit of 0.5mm wire about 50mm long to bridge the relay, it fried the wire and went open circuit after 30 seconds.... I have done that same test with bosch 044's and 040's with no issues...

AngryRB Grand Master

AngryRB

Posted
Posted

These bigger pumps pull a lot more amps, not sure what the stock fuse size is but a pump like the walbro 400/416 can pull over 20 amps which is way more than the stock wiring will cope with.

I wired a 416 up the other day (used 6mm to/from relay and 2.5mm in tank) then to test I used a bit of 0.5mm wire about 50mm long to bridge the relay, it fried the wire and went open circuit after 30 seconds.... I have done that same test with bosch 044's and 040's with no issues...

no wires being fried on mine, and no issues so far.

battery Mentor

battery

Posted
Posted

no wires being fried on mine, and no issues so far.

If the circuit is protected by the standard size 15A fuse then its unlikely you will burn anything apart from the fuse itself...

Be interesting to see what voltage the pump is seeing on your setup with stock wiring, i'd say you would be very close to the limit. Might be an idea to carry some spare fuses!

Wlabro.jpg

AngryRB Grand Master

AngryRB

Posted
Posted

yeah maybe its not stock then, i watched it being wired and put in by the tuner

interesting though, my battery light is on constantly and tuner said voltage is bit high, sitting on 15volts so must need a new reg or alternator, you'd think it would of blew a fuse by now.. have to look into that..

the 400L/hr pump is much quieter than the 255L/hr that it replaced, kind of miss the noise....

rob82 Mentor

rob82

Posted
Posted (edited)

If the circuit is protected by the standard size 15A fuse then its unlikely you will burn anything apart from the fuse itself...

Be interesting to see what voltage the pump is seeing on your setup with stock wiring, i'd say you would be very close to the limit. Might be an idea to carry some spare fuses!

Wlabro.jpg

Wow that's a pump, over 5l/min at 80psi - that's awesome!! Anyone tried one or got a cost?

Sorry just read the thread - have you tested the return flow to see if it matches the specs?

Edited by rob82
hnr32-25T Apprentice

hnr32-25T

Posted
  • Author
Posted

pump arrived today, hopefully fit it on the weekend, someone told me to put a 1 way valve in? but i don't really see the need. anyone else thinks it will help? i might need to pocket a roll of cable tomorrow at work, so wire from the rely in the fuse box down to the pump, do you route the wires the same as factory?

yeah i was thinking gtr pump, but i wanted something brand new and affordable.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Lock up the old for sale / wtb threads.

      By Duncan · Posted

      Ha, I've never pressed the X in all these years incase it removed the notification for all Admins
    • Duncan
      Blue/grey smoke after idle

      By Duncan · Posted

      I don't know, I've never done it that way, but 1. While it is an interference engine, there is still clearance between the valves and the piston at all points in the regular timing cycle 2. There is not a lot of distance before you can't catch the top of the valve stem any more I don't know if 2 is greater or less than 1. But 3. If it doesn't work out you are f**ked, engine is coming out to disassemble so it is a big bet.
    • Duncan
      Unpeeling the Orange

      By Duncan · Posted

      Semi slicks are horrible for road use, just use a high performance road tyre unless you really need the maximum grip. Noisy, unpredictable (amazing, until they are not), expensive due to very high wear and not good in cold and particular wet. And yes, it is a thing to store cars on stands instead of tyres if you know they are going to be parked up long term.....but who ever realises that a short park is going to stretch into years before it is out again!
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      I know in Australia you'll definitely get above 30c. Parked in the shade in Summer you'll be above that. 😛 But in cooler climates, you might get that warm driving on the highway for a bit, but you'd never get to full heat temp. I'll try and find some of my historical tyre temps between Aus summer and winter (be aware immin the warmer area of Aus too.)
    • sunsetR33
      Blue/grey smoke after idle

      By sunsetR33 · Posted

      I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
×
×
  • Create New...