Jump to content
SAU Community

Recommended Posts

Hi guys, I know this has been discussed in a few thread before, I'd just like some help identifying something.

Occassionally I get a high pitched squeal or whine from somewhere under the bonnet, hardly happens, I found downshifting into third or second and giving the car a bit of juice in high rev (3500 - 4000 rpm) and full boost makes the noise last for a second or so.

It's quite hard to replicate. Anyway from a few threads I have read people are recommending checking the turbo exhaust manifold etc for loose bolts and such.

I've taken off the turbo heat shield and not sure what to check. Most of the bolts were pretty tight already, I did notice that there was a bolt missing on the manifold and I'm not sure if there was an existing bolt there or not? Anyway I half screwed in a bolt in there to see, took the car for a spin, couldn't get the car to re-create the noise however I didn't notice a small chirp in second gear that may have been it starting.

Anyway, see the pic below. Is there anything in the pic I need to check, and should there be a bolt in the spot I marked?

turbobd.jpg

that bolt is nothing...it just holds the heat shield on

when mine started squealing it was the bolts that hold the turbo to the manifold (the one you can see in your picture actually as well as another one)...I tightened it with my hand and it was good again for a bit...

just feel around the turbo and manifold bolts to see if any are loose...

Had a mates car do that and it was a tiny split in a cooler hose (was the elbow under the turbo from

Memory) it would only do it under full boost and the split was really hard to find.... Long shot but I you don't find the other issues then it's worth a look :)

  • 3 weeks later...

Mine did this a while back, ended up being a intake gasket..

sorry, was that the gasket between intake manifold and the engine head or the gasket between the parts of the manifold itself? pardon my English, I'm from Russia))

Squealing is from tight or loose belts African Americanachi. Have a good feel of your visible belts. Maybe lay of the maccas. It could be your wife complaining. Mine does. Its a high pitched squeal the whole way there until her fat cake hole get filled. Nah kidding, she is a beautiful 5"10' 26 yro bitch! Or loosen your cam belt. But dont do that cos you dont know what the f**k you are doing.

same problem for a while things ive checked on inlet side cos that's where its coming from.the noise starts at about 7psi

manifold gasket.

disconnected factory boost gauge sender.

checked intercooler joiners for pin holes.

checked hoses for splits as this has happen be for to me.

even had a smoke test twice.

the only thing left for me is the pvc valve and hoses to the pvc

its a split hose some where i think cos it needs some psi be for forced open and whistle

Squealing is from tight or loose belts African Americanachi. Have a good feel of your visible belts. Maybe lay of the maccas. It could be your wife complaining. Mine does. Its a high pitched squeal the whole way there until her fat cake hole get filled. Nah kidding, she is a beautiful 5"10' 26 yro bitch! Or loosen your cam belt. But dont do that cos you dont know what the f**k you are doing.

epic post +1 Like

I had pretty much the same problem as you have. I had checked all the gaskets and still could not find the leak. It was also happening at 7psi and above. I had replaced all my vac hoses & all new clamps. Finnally I made this up and found the leak in about 5 mins.

Remove your intake from the front of the turbo, Attach the hose with valve to the front of the turbo, pump up using compressor. (no more than 10 psi) You should be able to hear the leak.

(Engine off, It will not hold pressure long. Just enough to find the leak)

Parts used to make this are

1 right angled silicone pipe from old stock intercooler pipes (or from any auto store)

1 screw in tyre valve

2 hose clamps

1 plastic pvc end cap (bought from a plumbimg store)

post-31128-0-39939900-1349689660_thumb.jpg

Edited by newboost
  • 6 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
    • Well the articals keep saying a Q50s (Skyline in Japan) with a new Manual gearbox. I like the talk about the new looks with the round tail lights. I hope they bring back the retro look like they did with the Z
×
×
  • Create New...