Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I just don't have the time to write up the guide, plus it may be a little confusing as it isn't an m35.

Che?

What do I drive? :P

Apologies for not putting up the comparison data, not so good with Excel so will take some time.

Excellent mod though and one of the first that should be done on a VQ25/VQ35 IMO

Che?

What do I drive? :P

Apologies for not putting up the comparison data, not so good with Excel so will take some time.

Excellent mod though and one of the first that should be done on a VQ25/VQ35 IMO

A tractor usually. :P

I forgive you Cam.

Is this the same principal: http://www.conceptzperformance.com/Cart/description.php?II=3434&Car_Type=G35&UID=20121009182338150.101.79.229

Of course I don't think it'd fit on a VQ25DET but sounds like the same concept.

Same concept, without the thermostat, and they didn't fixing the air bleed issue. That is the pathfinder coolant mod, I imagine that assembly will hold air in the thermostat too.

Mine also replaces the stock plastic bleed point with a billet alloy body and high pressure ball valve.

Is this the same principal: http://www.conceptzp...8150.101.79.229

Of course I don't think it'd fit on a VQ25DET but sounds like the same concept.

I looked at for some time Ryan and asked if it was bolt on and what, if any mods needed to be made to install.

The response?

"It is bolt on. It bolts onto the rear of the engine but you will have to cut and weld the pipe to attach to your coolant pipe"

(referring to the male/female fitting into the pipe on the driver side of the engine)

American "bolt on" is not the same as Japanese "bolt on". :no:

"It is bolt on. It bolts onto the rear of the engine but you will have to cut and weld the pipe to attach to your coolant pipe"

(referring to the male/female fitting into the pipe on the driver side of the engine)

American "bolt on" is not the same as Japanese "bolt on". :no:

What?

Don't think its weld on. The original piece for my car (dunno about NM35s) has a female end, and the goldy coloured anodised piece pushes in and secures into the alloy pipe.

The kit seems to have a lipped edge- so it wouldn't push in, but a bit of silicon tube and a couple of clamps would sort it out just fine.

I think the bigger issue is the cross over exhaust manifold pipe, and the extra stuff round the back there.

I like how their kit "lowers temps by 20 degrees", when I read that... The temps are still controlled by the stock thermostat ffs.

Ours is the same female fitting Alex, but the cast alloy pipe is a different shape for that reason, it would hit the crossover I think. ^^

OK, no steak knives please ... I am a vegetarian!

But I do have a relatively standard 2001 stagea and my Galaxy series 2 phone takes good pics so I am interested.

Also as a noob who took a long time to do the brake wire cut simply because I couldn't find pics I think its important to have good visual guides up here. Yeah Yeah I didn't take the pics either... next time I have the glove box out and on the back seat I will do a step by step on the 'brake wire snip' for new noobs. If you don't send me steak knives and do talk me through it, I'll do the same for this. :rolleyes:

You need a 2nd person to take the pics, otherwise the camera gets covered in oily fingerprints. :P

I have ordered the fittings, they should be around a week away. When they arrive I will have 3 kits ready to send out straight away. For anyone else interested I can make them up as I go.

You need a 2nd person to take the pics, otherwise the camera gets covered in oily fingerprints. :P

I have ordered the fittings, they should be around a week away. When they arrive I will have 3 kits ready to send out straight away. For anyone else interested I can make them up as I go.

Dibs!

  • 4 weeks later...

I'm going to try and fit this kit up on the weekend. Would I be right in saying it'll take an hour or two to remove the plenum and get down to the middle of the V to fit the top plate, about half an hour to actually fit the kit, and an hour or so to put it back together?

Should be about right. You shouldn't have to disconnect the fuel rail from the lines, just flip it over onto the drivers side guard.

Make sure you silicone the top plate, you don't want it leaking...

Shouldn't need to silicone it.

We used a new gasket for each of ours although the existing gasket would probably be good enough.

Gasket is the same as on a VQ35 in case you want to grab one from Nissan, Ryan.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to it's full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so damn hot in there, that made it all the more easy to remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. I was standing there looking at the car and said 'f**k it'. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...