Jump to content
SAU Community

Recommended Posts

They're supposed to be running Mobil petrol as far as I know. Their 98 octane is supposed to be Mobil Synergy. Iv used them before with no issues but who knows what they're up to these days tho. Iv had a bad batch of bp ultimate once too and car ran like shit.

Link to comment
https://www.sau.com.au/forums/topic/412504-7-elevens-fuel/#findComment-6598319
Share on other sites

was it 98 octane but? None of the 7/11 in my area have 98 only 95 which they call premium

I use their 95 in my xtrail & I'll get avg 500k's to a tank city driving not much better milage from bp or shell 95 maybe an extra 20-30k's if that

Link to comment
https://www.sau.com.au/forums/topic/412504-7-elevens-fuel/#findComment-6598602
Share on other sites

I've used my local 711 premium 98, had no problems. My local 7-Eleven had their tanks replaced recently after 10 or so years. I don't blame them for putting out botched fuels since it's not just them. Time goes by, tanks age and can get cracks where water seeps in. has anyone actually taken a sample and tested it?

Just sayin

Link to comment
https://www.sau.com.au/forums/topic/412504-7-elevens-fuel/#findComment-6598690
Share on other sites

I allways try to fill up at big popular servos,the lil quiet one that a filled up in on the central coast

a month back had very bad 98,high knock an my 33 ran like crap.

Got home put 98 in at a new servo and all good again no high knock,allso changed fuel filter.

Do a lot of ks so change it every 5 to 10000. :yes:

Link to comment
https://www.sau.com.au/forums/topic/412504-7-elevens-fuel/#findComment-6598764
Share on other sites

Time goes by, tanks age and can get cracks where water seeps in. has anyone actually taken a sample and tested it?

Just sayin

Yes, many 7/11s are built as recycled servos above old tanks.

Then again, there are quite a few old servos with big names on them too.

So just try and go to the places you trust.

And if you have mates over, let them know where those ones are eh?

Link to comment
https://www.sau.com.au/forums/topic/412504-7-elevens-fuel/#findComment-6598775
Share on other sites

Yeah if anyone is around Fairfield West, the 711 on Hamilton Rd corner of The Boulevarde had their tanks replaced less than 3 months ago, I'd be safe enough to say that the old ones are probably older than I am. Only two places that I go to fill up (unless I'm critically low) is that one and BP on The Horsley Drive near Tangerine St.

Link to comment
https://www.sau.com.au/forums/topic/412504-7-elevens-fuel/#findComment-6598849
Share on other sites

Any fuel station would be good if there's 98 octane and the queues are massive.

Fresh fuel's a guarantee with these stations.

I also never fill up if the tanker's there or has been there that day ;)

I assume it's because when they pump the fresh fuel in, it kicks up the sediments? If not then please explain!

Link to comment
https://www.sau.com.au/forums/topic/412504-7-elevens-fuel/#findComment-6600528
Share on other sites

As Terry said fancy looking convenience stores built on old tanks..they are more interested in selling donuts and slushies to fat people than quality fuel to motorists..

Even united are doing a far better job supplying quality fuels.

Its a real shame Caltex didn't get the buyout rights to Mobil..we could have had alot more eflex and quality vortex diesel available..

Instead we have to deal with Apu and his quik-e-mart junk. :(

Link to comment
https://www.sau.com.au/forums/topic/412504-7-elevens-fuel/#findComment-6600537
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...