Jump to content
SAU Community

Recommended Posts

G'day everyone,

This is going to grab a lot of peoples attention !

Looks like Jaycar Electronics have been doing a heap of work on making Automotive kits aimed straight at EFI/Turbo performance !

The first one that grabbed my attention was a kit version of the S-AFC, for around $80 !! Also is a handcontroller to tune it... As well as a fully indepenant electronic boost controller for around $80.. :headspin: :headspin: :headspin: :wassup:

The sad thing is that most of these kits are due out in September :)

A few other kits that will be on interest too, have a look at the links;

Digital Fuel Adjuster

Electronic Boost Controller

Hand Contoller for Digital Adjusters

Digital Pulse Adjuster

Intelligent Turbo Timer

Nitrous Fuel Mixture

Adjustable Temp Switch

Frequency Switch (shift light)

High Temp Switch (with display)

Duty Cycle Display

Voltage Switch

J

:(

Link to comment
https://www.sau.com.au/forums/topic/41261-jaycar-kits-s-afc-kit/
Share on other sites

Gotta love jaycar with the amount of load point mapping on the fuel adjuster it has to up there with many cheaper aftermarket ecu's and also the boost controller as well. For $220 for a boost controller, SAFC and hand controller it seems fairly cheap!

I wouldn't mind playing round with the Jaycar gear....

Since its to expensive for me to be mucking around with second hand jap gear. Only problem is though, I have very little idea when it comes to tuning hence we need someone to lead the way :) Even though im an apprentice auto elec me and my boss do nothin in the way of tuning.

I think we would all benefit in these kits to understand how our cars work better :)

Dammit!

I already got a Jaycar turbo timer.. which works sweet!

Wouldn't mind a controller to control the IC water spray automatically tho!

Now, if only I knew this and didnt buy my EBC, AFCII earlier!

They have a great one on Autospeed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...