Jump to content
SAU Community

Recommended Posts

hey all, recentley picked up a auto r34 gtt 4 door and im not sure what boost it should be running

mods are

t04e stage 3 turbo

external wastegate

3 1/2 straight thru exhaust turbo back to a nur spec cannon

greddy fmic

spitfire coils

tomei fpr 90 psi

100 oct premium

its running 14 psi at the moment as is is that too much or can it go more every where i have looked has suggested 14 on a stock turbo is the limit but is that the limit for the turbo or the tune

thankyou

Standard ECU?

That will be your issue, I'm suprised you managed to run 14psi through a bigger turbo on the stock ECU and it works.

I dont understand what a T04e stage 3 turbo is...... has it been worked to flow more?

Either way a T04 is much bigger then stock so I would probably stick it on a dyno to check AFR's or wind the boost down to be safe

or get an aftermarket ECU and push it

well ive had it up to 17 - 18 psi before by accident and was surprised that i never hit fuel cut im pretty sure it is a stock engine and ecu apart from them mods turbo specs are

Inlet Diameter: 4"

Outlet Diameter: 3"

Compressor Wheel: .57 Trim

A/R Compressor: .50 A/R

A/R Turbine: .63 A/R

forged compressor wheel

what boost do you suggest for the time being as the nearest dyno is atleast 500k

if you bought the car and it was running 14psi and you cant hear any detonation etc then I guess it will be O.K

I wouldnt wind the boost up put it that way. Remove the passenger kick panel and see if it has an aftermarket ECU or piggyback. Sounds like it must have something to be able to hit those boost levels.

See what you can find

The whole combination of mods sounds weird, maybe the previous owner is telling fibs?

What boost guage are you running and where is it readig its pressure from?

What boost control method?

Its either not not a std ecu or its not hitting those boost levels or its a time bomb...

blitz dual ebc

reading boost from the stock sender

not sure where the turbo is from i was told it is a t3/t4 t04e stage 3 from the owner it doesent look like a ebay special but it could be fpr was set when i got it havent played with it what should that be set on?

had a mate come look at it this morning he does alot with silvias he adjusted the fpr for me its at 55 now

apparentley it has a mine ecu i think he said but he also said that 14 psi on the bigger turbo will be maxing out my injectors

then he said that he didnt think they made a mine ecu compatiable with tiptronic auto

FPR would have been set so high to allow the stock injectors to keep up... Bad idea to turn it down from where it was set. Though it is also a bad idea to keep running it as is regardless.

a genuine 57 trim will flow in the region of 400 to 450 hp

buy some genuine 600cc+ injectors

throw away your fpr (or set it back to 1:1 rising rate)

get a decent fuel pump

get a standalone ecu

put it on the dyno and tune until you start seeing your intake temps blow out (turbo efficiency range exceeded) or you run into some sort of restriction

the auto box may cause you some issues ...

Turn the boost down and drive it gently till its fixed or you could be looking at a new engine.

Take the car to a tuner and get him to have a look at the Mines ecu to see if its tunable (most are not).

If not buy a stock R34 auto ecu and get a Nistune chip put in it. Get some Neo friendly injectors 550 or better.

Look in the tank and see if you have a new fuel pump. If not, buy one and install it if you can or if not add it to the injectors.

You will need a genuine Z32 afm (and plug) if you haven't already got one.

Ask around and find a good tuner (in another town if necessary) and hand him all the bits (or install the bits and tow the car to the tuner) and get it tuned (point out, although he should notice, that the FPR needs adjusting). If nothing has been damaged it should go well.

In the meantime baby the car - no mega boosting, no skids etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...