Jump to content
SAU Community

November Monthly Meet - Garage Cafe


Recommended Posts

  • Replies 119
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

HAHAHA Why don't we all just meet up in a massive carpark and order pizza??? Easier, tastier, and no one has to break balls to leave...

haha yeh good idea. and everyone get the gtrs out this time

LOL I think out of the whole attendance last time there was only 2 GTRs :/. Shame if you ask me. So many cars there that weren't even skylines but theres sooo many nice GTRs around. Take a look at the show n shine pics....

I give no f**ks for the cars or types of cars, it's the people that I like seeing at these meets...so I'm glad we've got more non-Skylines. Than Skylines. It's better than people ditching the scene / their friends after they sell their car.

I give no f**ks for the cars or types of cars, it's the people that I like seeing at these meets...so I'm glad we've got more non-Skylines. Than Skylines. It's better than people ditching the scene / their friends after they sell their car.

Ill fly my bird in

I give no f**ks for the cars or types of cars, it's the people that I like seeing at these meets...so I'm glad we've got more non-Skylines. Than Skylines. It's better than people ditching the scene / their friends after they sell their car.

just come in your friends skyline then lol

u give no f*cks? lol thats a new one

i thought it was "couldnt give 2 f*cks" lmao

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...