Jump to content
SAU Community

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

got cracking on ripping the rs260 front cut appart

interior all gone

front sturts pulled

ic piping ect all pulled

tommorow ill pull the shell off and hopefully start work on the s2 stagea to get the gtr running gear into it

no more interior

IMG_7576.jpg

passengers drive shaft was rooted

driver fell out and equally as rooted

IMG_7578.jpg

IMG_7577.jpg

the best thing is that all teh spare go into the s2 ready for transplant

IMG_7579.jpg

IMG_7580.jpg

slittle bit more progress

anyone need a bear front cut? $50

IMG_7726.jpg

also got stuck into the s2 so i can get the gtr motor in over the week

IMG_7727.jpg

if you need a ic kit $150( i pout up a for sale add for it)

other left over shit i dont need $50

good condition 25 clutch fan

IMG_7725.jpg

my thought exaclty gtr 260

i bought one at auction ( and was planning on importing it)

but after the auction my buyer said it was rusty as shit and had damaged chassi rails ( still had a 3.5 grade on the sheets)

so it was cut in half and sent over as i allready paid for it

i really could have made one out of spare r33 gtr parts i have in my shed

half the fun is building something as well

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...