Jump to content
SAU Community

Full-Race Ets-Pro Centre Diff Torque Split Controller Install Into R32 Gtr


Recommended Posts

Or maybe the wires to the control knob are crossed. See what it does when turned all the way to the right. Sounds like it's getting a crossed signal somewhere and system is being told give full pressure.

Ah yeah that's true too - I'll pull the whole lot out and have a look to make sure everything is attached correctly. I did it per the PDF in this thread but I could very easily have stuffed something up :)

front diff seems to be working overtime even when dialled back? When the car is cold and I reverse out of my driveway, the front of the car hops around a lot when I turn the wheel....almost feels like it wants to break something...didn't do that prior to installing the ETS Pro...I have a Nismo 1.5 way in the front.

more than likely everything is fine, but the 1.5way Nismo LSD is locking/unlocking to cause that vibration. Definitely a good idea to check wiring but I suspect its the clutches in your front lsd

sound exactly like the symptoms I had when TPS wires were wrong way round. If it does it when ETS is in RWD then I'd say it's mechanical.

hi, could you clarify what was wrong with the TPS? It is only a single output, 0-5V reference

Had a hyper tune intake with single throttle body. Replaced TPS but got wrong one. Was able to calibrate with motec but it was giving 5v at zero throttle and 0v WOT. When reversing it's the same as JH32 explained.

But tight diff is logical. Especially the Nismo. I had 1.5 Nismo in the rear and was tight as f###

  • Like 1

more than likely everything is fine, but the 1.5way Nismo LSD is locking/unlocking to cause that vibration. Definitely a good idea to check wiring but I suspect its the clutches in your front lsd

If I disable the ETS Pro though by "flicking the switch" to get into RWD, the shudder goes away.... I will try as tricstar mentioned anyhow once it's all up and running again and report back :)

the ETS-Pro maintains a low duty cycle and never fully opens/disconnects the clutchpacks, to keep 4wd response instantaneous. when you switch to RWD it goes to 0 duty and the clutchpack is fully open, there is no load on the diff.

I was talking to a mate last night about how tunable the ETS - pro is and it reminded me of something. My gtr had an OS giken 2 way in the front and when I first installed the ETS-pro I had the same problem. So I down loaded the software and plugged the unit into my laptop and reduced the preload, problem solved.

I'm surprised that wasn't your first suggestion Geoff?

So I'd try that before pulling it all out.

  • 3 months later...

Hi Geoff,

so in rear wheel drive mode the solenoid has 0% applied and at full locked up is set is at 100% .

Just curious as I was looking at making a LSD display to indicate the split load rear to front

EG :: 70% REAR, 30% FRONT.

More accurate for the end user rather than having the back light dim and brighten as an indication as to where you maybe set at when the adjustment changed.

Regards

Dave.

Edited by supercharged88

Hi all,

does anyone have this software you can send me please.

My email is [email protected]

I am running a Windows 7 OS laptop that I use for tuning only,

This has Windows 7 - 64 bit.

I have tried downloading the software over and over and I keep getting the following error.

I would very much appreciate if someone can pass on the download.

I forgot to mention I have loaded the USB software and works fine.

Kind

Regards

Dave.

post-51830-0-66976400-1444726585_thumb.gif

Edited by supercharged88

Hi Geoff,

so in rear wheel drive mode the solenoid has 0% applied and at full locked up is set is at 100% .

Just curious as I was looking at making a LSD display to indicate the split load rear to front

EG :: 70% REAR, 30% FRONT.

More accurate for the end user rather than having the back light dim and brighten as an indication as to where you maybe set at when the adjustment changed.

Regards

Dave.

Hi Dave, the correct way to do this is to read xfer Pressure (0-238psi) - Installing the pickup at the back of the transmission is not too hard to do, and ive seen an adaptor posted online for this:

91146d1437076729t-ets-pro-center-diff-to

Hi all,

does anyone have this software you can send me please.

My email is [email protected]

I am running a Windows 7 OS laptop that I use for tuning only,

This has Windows 7 - 64 bit.

I have tried downloading the software over and over and I keep getting the following error.

I would very much appreciate if someone can pass on the download.

I forgot to mention I have loaded the USB software and works fine.

Kind

Regards

Dave.

from the electrical engineers, please let me know if this works for you:

cleardot.gif

"I recommend to download from this link (V1.1):

http://dccdpro.com/main/wp-content/downloads/DCCDPro.rar

Then extract the two files and keep them in one folder. run the .exe and if Windows 7 or 8 need to run in compatibility mode.

If they use this link(V1.2):

http://dccdpro.com/main/wp-content/downloads/DCCDPro.exe

Run the .exe and if Windows 7 or 8 need to run in compatibility mode.

I have checked and all are in good shape.

the ETS-Pro maintains a low duty cycle and never fully opens/disconnects the clutchpacks, to keep 4wd response instantaneous. when you switch to RWD it goes to 0 duty and the clutchpack is fully open, there is no load on the diff.

Does this mean the clutch packs are always slipping and does this accelerate wear appreciably?

^^No. If you look at R33 and R34 oem the system will do this. The result is no lag in torque split response. Compared to R32 where the oem computer is very old and outdated, very slow response times due to the pressure dropping off too far. If you have a very high power application and are concerned about xfer case, it is a good idea to install a cooler and/or consider adding an 11th plate/disc to the wet clutch

Edited by Full-Race Geoff

Thanks Gary, I do indeed have an R32 so hence very interested in the system. Was just concerned that - particularly in the case of the 32 - making a system that has x duty then run constantly at x+1 will break or wear something exponentially.

Power levels not withstanding, from what you're saying can I take it that this won't be an issue?

  • 3 months later...

hi Jimmy, depending on your location - Galvsport has done right by my customers: http://www.galvsport.com/ Try speaking with Josh, they are great to work with

  • 5 months later...

Hi Geoff

 

I am really keen on installing one of these.  Is it best to purchase from full race website direct?  

Any workshop in Victoria you know who is experienced in installing the system and check to make sure it operates as intended

Thanks

Matt

Edited by tangomatt

hi matt, you can purchase directly from our website or you can call our office.  Im not sure who to recommend for install in victoria.  I will ask a few contacts.  feel free to email me directly at [email protected] with any other questions

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...