Jump to content
SAU Community

Recommended Posts

Hey guys, had my SAFC wired up and took it down to Unique Autosports to have it tuned. On its base run the car only managed a pathetic 120.8rwkw (down almost 11rwkw from its previous) and was leaning out fairly badly, about 13:1AFR on stock maps. SAFC was adjusted to increase fuel by 10% from 3000rpm-5000rpm and 3% at 6000rpm (12.6AFR) and the car gained 2.8rwkw :(. Got the car booked in for a smoke test at Unigroup Engineering to check for vacuum leaks, changed fuel filter today, will drop in a Twin Turbo 300ZX pump and get fuel pressure checked over the weekend. Kinda weird that the car had lost so much power yet still trapped 95-97mph at WSID only 3 weeks beforehand with nothing changed since then. Any other idea's as to why it could be running so lean?

would you even feel the difference of 11kw.. could of been some lower octane fuel or the dyno, hows the fuel pump?

definitely need some turbo action to do that beast some justice. :yes: ive driven an NA that was much better than a twin turbo though so make sure its not clapped out.

Edited by SliverS2

Its an NA and they usually run 11.5:1AFR stock so 13:1 is a huge difference on a stock ecu. Also i'm currently the 2nd fastest NA 300ZX on Aus300zx so its definately not "clapped out".

Its an NA and they usually run 11.5:1AFR stock so 13:1 is a huge difference on a stock ecu. Also i'm currently the 2nd fastest NA 300ZX on Aus300zx so its definately not "clapped out".

you should be making more power at 13:1 than 11.5:1 unless it is pinging it's head off and the ecu is backing the timing off

you should be making more power at 13:1 than 11.5:1 unless it is pinging it's head off and the ecu is backing the timing off

This listen to this. You want to be as close to 14.7:1 as you can without pinging and compromising timing.

This listen to this. You want to be as close to 14.7:1 as you can without pinging and compromising timing.

Actually, no you don't.

14.7:1 will provide a perfect stoichiometric burn, ie, all fuel is used, and all oxygen is used.

15.4:1 is a good mixture for cruising on.

12.0 to 12.5:1 has been shown numerous times to be the AFR that an engine will produce it's most torque from.

At 12.5 :1 you can really hammer the timing it and get it producing maximum combustion pressure at top dead centre rather then when running 14.7:1 where it makes maximum combustion pressure after top dead centre.

Its an NA and they usually run 11.5:1AFR stock so 13:1 is a huge difference on a stock ecu. Also i'm currently the 2nd fastest NA 300ZX on Aus300zx so its definately not "clapped out".

If you're running an AFM, clean it with CO Contact cleaner.

Check your air filter too.

Make sure you're running the same oil type as last time (throw in some fresh oil with a fresh filter!)

Check your TPS is set right and sending the correct values.

Check your coolant temp sensor is reading correctly. (voltage VS temperature check)

Pull your injectors and have them cleaned and flow tested.

Have you check your fuel pressure is still good?

Is your cat all okay?

This listen to this. You want to be as close to 14.7:1 as you can without pinging and compromising timing.

As mbs206 said, you don't want to go as lean as 14.7:1. However, at 13:1 it should still be making good power, but if it is tuned to be at 11.5 then it is probably pinging and the ecu backing the timing off

Actually, no you don't.

14.7:1 will provide a perfect stoichiometric burn, ie, all fuel is used, and all oxygen is used.

15.4:1 is a good mixture for cruising on.

12.0 to 12.5:1 has been shown numerous times to be the AFR that an engine will produce it's most torque from.

At 12.5 :1 you can really hammer the timing it and get it producing maximum combustion pressure at top dead centre rather then when running 14.7:1 where it makes maximum combustion pressure after top dead centre.

hmm this is interesting, I'll have to do some reading on this. Is this for all NA engines or does it noticeably change engine to engine

that is for most NA engines. to put this into perspective, the stock ecu on the missus SSS pulsar (natro sr20) runs around the high 11:1 mark in the mid section of the rev range and drops to about 11:1 at high rpm. NA's can run a fraction leaner at WOT than turbos can, but not that much.

just like turbos, natro cars still run between 14:1 and 15:1 at cruise via the o2 sensor

hmm this is interesting, I'll have to do some reading on this. Is this for all NA engines or does it noticeably change engine to engine

for petrol piston engines.

Specific engines will change slightly depending on design, but mainly the above.

Ah ok I always thought NA's could run a lot leaner than turbos. I suppose the added compression and timing makes up for that.

You can run it leaner, the difference is, lean is not where the power is made.

Once you start tuning with an SAFC you will find you want to adjust your timing as well. You could use an SITC if you can find one or if Nistunes work on N/A you would be better to do that.

Few things done, did a dodgy fix on the Vacuum leak till i can sort some stock Intake pipes out and dropped a Twin Turbo 300ZX Pump in yesterday and took it for a quick drive tonight, Injector Duty Cycle was stable(use to get random spikes) and car felt a bit sluggish in comparison to before so i'm guessing the AFR has lowered back to stock(plus the SAFC adding more fuel in) but can't confirm till i get a wideband on there.

Edited by Super Drager

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kinkstah, no, coilovers aren't illegal, especially as a bolt straight in. The illegal part will be if they're altering suspension geometry beyond factory limits, or the ride height is not legal.   Sounds like the blue slipper just didn't want to deal with any later possibility of mods appearing on the car.
    • The problem has always been that coilovers are able to be adjusted, almost at any time, to be too low. Most people who ever get/got defected for/with coilovers were actually afoul of the minimum ride height rule. So the interpretation by cops/inspectors was always that it is pointless to allow numpty to raise his coilovers and get the car inspected/cleared, then just drop them back down again as soon as they get around the corner from the inspection station.  This led to the interpretation that they were illegal unless rendered such that they can't be adjusted (ie, collars welded to the body, that sort of thing). That may or may not have ever actually been the official line, but I'm pretty sure it's not considered to be a solution these days. Coilovers themselves fall under clause 3.2 b of that manual, because they are an "installation of a variable ride height system" and they don't fit the exclusions in that clause (which point to air springs and other pneumatic adjusters). So, as per previous statements, they require engineering cert to be legal on the road. Once you have such cert, provided you do not adjust them outside the height range covered by the cert, you are OK. Without, you have an unroadworthy vehicle.
    • Here E10 is the cheapest fuel. And general advice is to not use it unless you hate your car. From what I remember it clogs up stuff in the fuel system or injectors?  With US/Canada being E10 across the board, does that mean that all fuel there is terrible?
    • Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW ) Edit: I checked. They aren't. https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
×
×
  • Create New...