Jump to content
SAU Community

Recommended Posts

sweet gig for Mark

It is for Mark. Although I am sad to hear about Mark's retirement from F1 (big fan), I am pleased to hear he will remain in high level racing.

Le Mans et la serie endurance is very much on my watch list and rather exciting to know Mark will now be part of it.

Mixed feelings about how he announced it. Good on him for being "no notice Webber" and doing it on his terms. But six for his mechanics and those close to him in the team to not hear it from him directly.

I suspect the way he announced it has done him no favours with regards to trying to bag a few more GPs before year is out. Oh well...have to decide whether I go to Singapore, India or Japan. Most likely Japan...over India and street races suck for access and spectating!

Mixed feelings about how he announced it. Good on him for being "no notice Webber" and doing it on his terms. But six for his mechanics and those close to him in the team to not hear it from him directly.

I suspect the way he announced it has done him no favours with regards to trying to bag a few more GPs before year is out. Oh well...have to decide whether I go to Singapore, India or Japan. Most likely Japan...over India and street races suck for access and spectating!

Well I am off to Singapore - but Japan may have been a better choice. Anyway one last dose of atmo motors and MW.

Post race concert in Singapore? Fkn Justin fkn Beeber. FFS the fkrs fkn fkd.

Q&A with mark webber

Following the announcement that Mark Webber has signed with Porsche to join their WEC and Le Mans 24 Hr team campaign in 2014 and beyond, www.markwebber.com asked him the burning questions:

Why have you made the decision to join Porsche in the WEC at the end of the season?

MW: The timing is perfect to join a fresh programme. It’s a sensational challenge and opportunity for my future to work with one of the most famous marques in motorsport.

How do you feel about returning to Le Mans after what happened in 1999?
MW: I accept that motor racing is dangerous but Le Mans is one of the most famous circuits in the world and to be honest, I still see it as unfinished business and I want to do well there. Le Mans can be cruel as we’ve just seen, but it’s incredibly rewarding and that’s part of the allure.

Did the events of the Malaysian GP (or other well documented inter-team incidents) influence your decision/make your mind up?
MW: No, I’ve had a personal plan and I’ve stuck to it. This is the next chapter.

Were you pressured or encouraged to leave RBR by the team or was it purely your decision?
MW: I never asked the team for more work but I’ve remained in touch with Dietrich Mateschitz over the last six to eight months and he’s been absolute quality for me. Going forward I will remain tightly inside the Red Bull family, working with the brand, and watching and supporting fellow Red Bull athletes push the boundaries.

You are one of the oldest drivers on the grid, has your age affected your driving and was this a consideration in your decision to leave?
MW: Of course you want to do your whole F1 career at the age of 25. Ask any sportsman or woman in their mid to late thirties and they will tell you that things don’t become any easier. That’s just a fact of professional sport.

Did you have options to stay in F1?
MW: Yes but since Formula One as a category wasn’t on my radar for 2014, they weren’t a consideration for me.

Will you rule out a return to F1 should another opportunity present itself in the future?
MW: I’d say it’s extremely unlikely, particularly given the new direction the category is going in. You would be out of touch very quickly.

Finally, what will miss about Formula One?
MW: I realise F1 is seen as the absolute pinnacle of motorsport and I’ve worked with some incredible people, in particular Adrian Newey. I’ve driven in some of the toughest and most challenging conditions and circuits, and against some incredible drivers which I’ll continue to do until the end of the year. Will I miss some of this? Yes, of course, but time doesn’t stand still for anyone and it’s time to move on to my next challenge.

http://www.markwebber.com/on-the-track-news/2013-season/mark-webber-qa-2014-and-beyond/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...