Jump to content
SAU Community

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

I am like sooooo one step ahead of you :rofl:

LW.

Actually, I am one step ahead of you :) My car is already here :P

Unfortunately, it has been stuck on the docks for over 2 months. :( Even worse, it's not even in NSW. I hope it hasn't been stripped. Thankfully, my other set of mags didn't get put with that car.

Guest two.06l

Silver 93 r32 gtr import

Engine

· Micks Metalcraft 4” Intercooler

· Dual Blitz blow-off valve

· Top Secret Super radiator, Trust hi psi cap

· External 19 row oil cooler with thermostat

& remote filter (not fitted for D.C.)

· Trust clear timing cover

· Trust timing belt (new tension pulleys)

· HKS vernier cam gears

· Nismo valve stem seals & bronze guides

· Knife edged and ported head

· Tomei 260 degree camshafts

· Tomei 1.2mm head gasket

· Tomei oil restrictor kit

· Tomei sump baffle kit

· N1 oil pump & water pump

· Cryogenic treated, crack tested & linished crank

· Cryogenic treated, crack tested, shot peened,

resized, closed & honed polished conrods

· ARP rod bolts & head studs

· Cryogenic treated Aries forged pistons

with teflon coated shirts

· Total seal gapless rings

· Deburred, honed & crack tested block

· Clevitte 77 main & rod bearings

· HKS 2530turbos with HPC coated

turbine housings

· HKS manifolds, HPC coated

· HKS dump pipes with separate

wastegate HPC coated.

· HKS adjustable waste gate actuators

· Tuned length engine pipes

· HKS dunk megaphone 3” exhaust

· HKS piping kit (turbos to plenum)

· 80mm Z32 airflow meters

· HKS super power flow filters

· Sard 720cc injectors

· Trust fuel rail (twin inlet)

· Sard fuel pressure regulator

· Twin Bosch motor sport fuel pumps

· Performance MetalCraft surge tank

· 500hp Bosch swimmer lift pump (in tank)

· Custom alloy catch tank

· Nismo engine mounts

. Splitfire ignition coils

Suspension and Brakes

· Cusco master cylinder brace

· Cusco front strut brace

· Cusco rear strut brace

· Auto Select A pillar braces

· Endless brake pads

· HKS hyper damper coil overs

· JIC rear upper link arms

· UAS front upper link arms

· Rear subframe bushes

· UAS 330mm front brake rotors (not fitted for D.C.)

Electronics

· Apexi Power FC computer

· Apexi AVC-R boost controller

· Apexi turbo timer

· Carel inlet temp meter

· 300km speedo

· Auto meter 0-35 psi boost guage

Driveline

· Jim Berry modified clutch set-up

· Nismo lightened flywheel

· Exedy super single clutch plate

· Nismo 4800 pound pressure plate

· Rebuilt Nissan GTR gearbox with Cryogenic treated internals

· Nismo gearbox mounts

· Falken Azeni tyres

· 17x8 front & 17x9 rear Super Tourer alloy rims

Owner/Driver:

· Stacey Diemar

Research / Development / Tuning:

· Dirt Garage Crew: Paul, Darren, Luke, Duncan, Peter, Patrick

· DP’S Motorsport

· Croydon Racing Developments

Sponsors:

· Wanted,

Silver 93 r32 gtr import        

Engine

· Micks Metalcraft 4” Intercooler

· Dual Blitz blow-off valve

· Top Secret Super radiator, Trust hi psi cap

· External 19 row oil cooler with thermostat

& remote filter (not fitted for D.C.)

· Trust clear timing cover

· Trust timing belt  (new tension pulleys)

· HKS vernier cam gears

· Nismo valve stem seals & bronze guides

· Knife edged and ported head

· Tomei 260 degree camshafts

· Tomei 1.2mm head gasket

· Tomei oil restrictor kit

· Tomei sump baffle kit

· N1 oil pump & water pump

· Cryogenic treated, crack tested & linished crank

· Cryogenic treated, crack tested, shot peened,

resized, closed & honed polished conrods

· ARP rod bolts & head studs

· Cryogenic treated Aries forged pistons  

with teflon coated shirts

· Total seal gapless rings

· Deburred, honed & crack tested block

· Clevitte 77 main & rod bearings

· HKS 2530turbos with HPC coated  

turbine housings

· HKS manifolds, HPC coated

· HKS dump pipes with separate  

wastegate HPC coated.

· HKS adjustable waste gate actuators

· Tuned length engine pipes

· HKS dunk megaphone 3” exhaust

· HKS piping kit (turbos to plenum)

· 80mm Z32 airflow meters

· HKS super power flow filters

· Sard 720cc injectors

· Trust fuel rail (twin inlet)

· Sard fuel pressure regulator

· Twin Bosch motor sport fuel pumps

· Performance MetalCraft surge tank

· 500hp Bosch swimmer lift pump (in tank)

· Custom alloy catch tank

· Nismo engine mounts

.               Splitfire ignition coils

Suspension and Brakes

· Cusco master cylinder brace

· Cusco front strut brace

· Cusco rear strut brace

· Auto Select A pillar braces

· Endless brake pads

· HKS hyper damper coil overs

· JIC rear upper link arms

· UAS front upper link arms

· Rear subframe bushes

· UAS 330mm front brake rotors (not fitted for D.C.)

Electronics

· Apexi Power FC computer

· Apexi AVC-R boost controller

· Apexi turbo timer

· Carel inlet temp meter

· 300km speedo

· Auto meter 0-35 psi boost guage

Driveline

· Jim Berry modified clutch set-up

· Nismo lightened flywheel

· Exedy super single clutch plate

· Nismo 4800 pound pressure plate

· Rebuilt Nissan GTR gearbox with Cryogenic treated internals

· Nismo gearbox mounts

· Falken Azeni tyres

· 17x8 front & 17x9 rear Super Tourer alloy rims

Owner/Driver:  

· Stacey Diemar

Research / Development / Tuning:  

· Dirt Garage Crew: Paul, Darren, Luke, Duncan, Peter, Patrick  

· DP’S Motorsport

· Croydon Racing Developments

Sponsors:

· Wanted,

Nice setup there stacey!

Merli,

Not yet, have not had the car 100% since PAS when it got the 421hp. But now with new twin plate clutch, fixing the knock problems and a new front cv I hope to get down to the plex when racing starts again.. Though I have no illusions to my crappy driving abilities, I'd hope to get into the 11's with that power figure...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...