Jump to content
SAU Community

Recommended Posts

so i have a front mount intercooler and when i boost up its quite evident that my a/c gets warmer, due to the fact the hot compressed air in the intercooler is stealing the cold air before my condenser. i no the obvious fix (remove the fmic) but i want to know

will twin electric thermo fans make that much of a difference to the air flow?

has anyone had experience in this area?

are there even any kits out there?

if anyone has them how have you set them up?

all advise will be appreciated.

cheers :)

p.s r34 gtt rb25det using a blitz return flow front mount, gtrs turbo on 1.2ish bar

When throttle is planted the compressor turns off to give you more power and not stuff the compressor bearings too no doubt.

Turn it off if your nailing it repeatedly as the compressor clutch will will slamming in/out at full noise

yeah the a/c is nice and cold just idling and cruising, i would like it to be colder so i have to check the pressures and get a thermometer on me air vents, it doesnt get hot when upping it just not as cold, feel a change. and on a hot day it sucks. and the boosting is on short stints lasting one gear or so driving around town as such, taking off from lights ect. but its a black car, dealing with 36deg days a humidity (love central queensland), but yeah its just that difference when i give it some. but sounds to me i have to deal with it because of the front mount, so more vent sounds like the go?

Edited by Jayden.K

I've used my A/C while at the track on 35C days and it was cold as it would be while driving about. But I do notice as I climb up the revs, the air gets warmer until 7k (pretty much full warm), then I enter a turn and exit and it's cold again. So I can confirm the A/C turns off at WOT.

I actually just notice my a/c electric fan doesn't work when the a/c is on. Is there more requirements it needs to turn on or should it be working??? And I also notice the condenser has had lines blocked off because of a dint. So without checking pressures I'm confidient where a leak is if I put dye in the system. If its even leaking. But main issue is that electric fan should be going yeah??

It doesn't switch on unless the coolant temp is approx 95C+, I can't remember if this is true if the A/C is switched on (or if the A/C runs the fan regardless of coolant temp) .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...