Jump to content
SAU Community

Recommended Posts

You can get good dampers from concept z performance or statik performance... The cost is all around the same $120 shipped to AU.

As for install, no you don't need to drill holes and installation takes about 20 mins with the correct tools

Have finally started on the mods for my 2001 300gt.

IMG_1819_zpsfda5c766.jpg

I started with the Z Tube, which was easy enough to install. For a simple and cheap little mod it doesn't hurt to have and the car sounds nicer at higher revs.

IMG_1768_zpsfd55b0cb.jpg

Scotty nm35 installed a Transgo Shift Kit into my 5 speed automatic transmission and all I can say is WOW. The car still feels nice when cruising but when you plant your foot in either drive of manual mode the car turns into well, a different car. Nice, crisp and sharp changes and almost instant. Definitely worth it!

IMG_1983_zpsbe858896.jpg

At the same time we also installed a Stillen Gen 2 True Dual Stainless Steel Catback. The sound it produces is a nice and low tone on idle but once you hit 3-4000 rpm it shows you why it cost me so much haha. The twin tips also look great and it feels like there were some gains from it.

IMG_1970_zps91ef8d26.jpg

IMG_1981_zps08a7abb1.jpg

IMG_1982_zps12e87316.jpg

I'd always planned to change the rear differential seeing as opens are gay but this mod got fast tracked due to some clearance issues regarding the exhuast and the drivers side flange on the factory diff (only 2001 models have these flanges). So we installed a 6 Speed Manual 350Z LSD. This changed the final drive from approximately 3.13 to about 3.5. Less top speeds but moar low ends which is what these cars need seeing as you can't even hit the top speed due to the speed limiter. This mod fitted perfectly with only the yolks between the open and lsd being switched. Thanks to Scotty again.

IMG_2014_zps06f6ee1c.jpg

So now the car has nicer shifts, sounds cool and can do double peggers so where do you go from here? Well here's the kicker. Notice how when you're looking to launch in the 250 and 300 (not sure about 350) you can only stall up to 2k rpm? This is due to throttle restrictions when pressure to the brake is applied, the car will also lag for 3 seconds after your foot is off the brake. Well thanks to Scotty the car now revs past 2k and well as high as you want due to a modification in the ECU where the brake sensor is altered. Now coming out of corners you can hit full throttle instantly as well as being able to stall the car up for a nicer launch or burnouts. Whatever floats your boat really. Now it's time to save again and get some suspension mods happening and maybe some nicer wheels ;)

Hey Sam, some practical mods you've done there mate. I like the dual tips on the sedans it completes the back in my opinion. Your the first person I've seen have a good crack at modding a 300GT, you've done well

So now the car has nicer shifts, sounds cool and can do double peggers so where do you go from here? Well here's the kicker. Notice how when you're looking to launch in the 250 and 300 (not sure about 350) you can only stall up to 2k rpm? This is due to throttle restrictions when pressure to the brake is applied, the car will also lag for 3 seconds after your foot is off the brake. Well thanks to Scotty the car now revs past 2k and well as high as you want due to a modification in the ECU where the brake sensor is altered. Now coming out of corners you can hit full throttle instantly as well as being able to stall the car up for a nicer launch or burnouts. Whatever floats your boat really. Now it's time to save again and get some suspension mods happening and maybe some nicer wheels ;)

Do you know what he did exactly because I would be very interested in getting this done. Sick of the lag and rev limit...

Got my engine torque damper put on today.

It's has taking a while for it to settle in.

when I first drove off I could feel the car shaking but now it's fine.

it shakes at standstill and idle, but once it gets moving it does not shake any more correct?

how long did it take to "settle"??

Got my engine torque damper put on today.

It's has taking a while for it to settle in.

when I first drove off I could feel the car shaking but now it's fine.

How many engine mounts have you broken?

After 30 mins driving it feels better. but that might be me getting used to it. I drove off today with it shaking then after a while it felt better.

Taking it off later this week.

Cons out weigh the benefits.

it shakes at standstill and idle, but once it gets moving it does not shake any more correct?

how long did it take to "settle"??

ripped the dash apart today. sick of am radio due to lack of frequency converter and a Japanese pop cd stuck in the factory single din player

too bad the solder I have is garbage so couldn't finish the job today. pulled out the non-functional spaghetti junction carmate alarm too, all the wiring can be seen on the drivers floor, along with the box on top of the dash... much cleaner under the wheel now. locally installed mongoose looks so much neater under there

d0d2f76b-541c-40f9-af2e-ab4e37554c94.jpg

Edited by junkie

Finished today after getting some decent solder... had to reset the airbag light though (thanks youtube), as I unplugged the passenger one while removing the glovebox. Polished the plastic on the aircon/time/temp display while i was at it too, was all fuzzy before, nice and clean now.

While I had everything in pieces, also fixed a rattle from the aluminium trim around the gear selector with some sticky felt pads, was driving me nuts before

oh and highly recommend these for any interior work, i did the whole install without any trim damage whatsover:

http://www.bojoinc.com/index.php/composite-hand-tools/ath-m-ngl.html

Edited by junkie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...