Jump to content
SAU Community

Rb25Det Neo 4Wd Blown Head Gasket And Spun Bearing Complete Engine For Sale

AAA34T
 Share

Recommended Posts

AAA34T Community Regular

AAA34T

Posted
Posted

This engine is from a 1998 nissan stagea rs4 auto its an rb25det neo 4wd it has 180000kms

Head gasket was changed at 110000 and head was serviced (i overheated it)

I overheated it again at 180000 when the radiator gave way but shut it down to late and spun a main bearing (knocking in the bottom end)

All parts there good for project engine alternator, ac,turbo , inlet manifold ,exhaust manifold, and heaps more

$650 neg cash must pick up from gladesville

email me [email protected]

fatz Grand Master

fatz

Posted
Posted

what condition is the head? or os it beyond salvageable? warped or cracked?

hi mate, i have bought this car from adam and am looking to sell the engine etc so flick me a pm

im located in western sydney (lower blue mountains)

pete

AAA34T Community Regular

AAA34T

Posted
  • Author
Posted

what condition is the head? or os it beyond salvageable? warped or cracked?

sorry about the late reply i dont check sau much the head should be fine but it is still on the engine so i am not 100% sure on the cond but when it was taken off the first time it was good and i had it crack tested and valves done and everything was tested and the guys at thornleigh cylinder heads said it was all great so we put a new head gasket arp studs and all ned timing belt,seals,waterpump,and the rest and everything was running great until the radator gave way and it the engine got to hot again. Pm me if anyone needs more info so i get an email direct to my phone just quicker thanks

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...