Jump to content
SAU Community

Recommended Posts

Just wondering how long it takes your car to reach normal operating temp from a cold start under normal (no lead foot) drive?

I've got a stock as a rock R34 GTT apart from an apexi pod...it takes under 60 secs to reach the half way mark on my engine temp gauge. Using Cusco 5w 40 oil.

Cheers

It should probably take a little bit longer than that, but these hot days may be causing it to come up to temp a bit quicker. I'm assuming that is while you are driving? In which case how you drive will also play a part.

If that is 60 seconds of idling then unless it is super hot where you are, that is a little bit on the quick side as it takes longer when idling.

I should add that it may just be that the gauge is just a little bit happy and there is nothing wrong with the cooling system. The gauge gets to the normal point from about 65 degrees and above

yeah mine takes not long at all really. driving at suburban speeds maybe about 2mins and its up to temp or if i start it up and jump straight onto the open road (100kph) it comes up real quick yeah maybe 60 seconds

Before with my almost dead thermostat, it would take 20+ mins.

But after swapping over to a new one, it'll take roughly around 2-3kms @ 60km/h.

As mad082 said, it really depends on the weather as well. If it's a really hot day, then the thermostat will open a lot sooner versus a cold night where it'll stay closed for longer so the engine can warm up properly.

Thats only coolant, temperature,

+1, so you shouldnt use that as an indicator that its ready to be driven hard. You want the oil temp to be normal before you do that, and it takes a lot longer.

i must have somthing wrong then, according to the power fc, im at approx 50degrees within 5min. living on acreage it can take that long to get out the front gate with a toddler getting his seatbelt on, lol, then after 5-10min at 60-80k/hr im upto high 70's,

do you guys recommend a standard thermostat or aftermarket? and what coolant temp is considered the normal?

Edited by AngryRBGTX

82 degrees is normal. and definitely go standard. go genuine nissan. you can buy plenty of aftermarket ones with lower temps, but they are a waste of time and money, partly because they will make you use more fuel.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...