Jump to content
SAU Community

For Those Running Nismo Coppermix Twin.....

Goombeh
 Share

Recommended Posts

Goombeh Collaborator

Goombeh

Posted
Posted

So I've recently had my Nismo Coppermix Twin plate installed in the GTR and I'd read so much about them being very drivable and stock like.

Now I've only driven maybe 50kms so may be too early and may need bedding in, but immediate impressions are that it is very... very light. Doesn't feel like it will hold power, almost feel like I need to take the booster off to get more feel. But it's very quiet and seems very strong. It's very quiet in neutral or with clutch dissengaged.

Now my question is for those who run one, is it normal for it to cause some driveline judder on gradual take up? My searches are suggesting no, however I have read that this is commonplace on twins. I can drive around it of course by taking it up with more revs, but wondering if I should be looking into replacing gearbox or engine mounts or if this may be considered normal. My old Clutch had a very slight judder only when cold.

What do you think?.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

That's what makes the Nismo Coppermix so driveable. It's not filthy heavy like a OS twin plate for example which over time is like kicking a bag of sand over and over.

The first 500-1,000kms it will be a little bitey, it will settle down though. So give it a little while before worrying about minor shudder.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

it says that these clutches make noise and vibrations

Yeah just so that when it does make the slightest noise (and it literally is non-existent) - people dont come back and complain.

As the plates get lower/wear they will get noisier, just how it goes.

Iron Chef Grand Master

Iron Chef

Posted
Posted (edited)

My only complaints are it's a bit rattly on idle in neutral (clutch out) because of the flywheel, and slips a bit when cold, aside from that it's brilliant, very light to use and bites hard on high RPM take-offs...

Edited by Iron Chef
LotusGTR Veteran

LotusGTR

Posted
Posted

I've got one and I could not fault it in any way. When it was installed it was very 'bitey' (probably me just getting used to a twin) but I did get it adjusted (dunno what was done) and it was so much easier to use. No noises what so ever. Not heavy. Very user friendly. No driveline shudder under any circumstances.

Have only launched in 2WD mode but it was a 2nd gear start from standstill. No dramas and was really easy to modulate.

Ace clutch. Should be for the money.

nomnomv8 Rising Star

nomnomv8

Posted
Posted

Ive got the Coppermix Twin C-spec in mine and have nothing but praise for it. By far the easiest twin plate I have ever driven and at the same time has a real good bite to it. A few of the guys have mentioned noise issues - you can hear it on the odd occassion in neutral however its pretty subtle and honestly nothing to lose sleep over.

Give it about 500km or so of driving (start/stop as opposed to highway kms) before you give it a launch, I guarantee you it will definately "hold the power" ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 gtr transmission strength, billet plate

      By GTSBoy · Posted

      Just put skinny tyres on it.
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • Piggaz
      R32 gtr transmission strength, billet plate

      By Piggaz · Posted

      You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...