Jump to content
SAU Community

Recommended Posts

I have a collection of BNR32 bits that i need to get rid of, bundling welcome!

I can post/courier interstate so just ask!

Please sms 0414933611

I've put photos of most things below

NEW tailshaft $250 ono

NEW rear diff R200 no shafts $1000 ono

NEW cailer seal kits $20

NEW front diff rebuild kit $100

NEW front hubs $50 ea

NEW wheel bearings $50 ea

NEW Tein shocks $100

NEW brake master $70

NEW rear calipers $120 pair

Used nismo pull clutch $50

Used front diff ring and pinion only $20

Used ECU (unsure of stock or chipped) $50

Used front rotors $30 pair

Used set of standard suspension VGC $200

post-22498-0-88169700-1358758298_thumb.jpeg

post-22498-0-62745900-1358758306_thumb.jpeg

post-22498-0-12190000-1358758315_thumb.jpeg

post-22498-0-64670700-1358758580_thumb.jpeg

post-22498-0-32217800-1358758589_thumb.jpeg

post-22498-0-66406300-1358758602_thumb.jpeg

post-22498-0-03428100-1358758668_thumb.jpeg

post-22498-0-43516700-1358758704_thumb.jpeg

post-22498-0-47142400-1358758715_thumb.jpeg

post-22498-0-43628500-1358758728_thumb.jpeg

post-22498-0-62437800-1358758873_thumb.jpg

Edited by Squishy
  • 3 weeks later...
  • 3 months later...

still have this shit in my garage

R32 GTR
NEW OEM
tailshaft $250 ono
rear diff R200 no shafts $1000 ono
caliper seal kits $20
front diff rebuild kit $100
Tein shocks $100
brake master $70

Used parts
nismo pull clutch $50 suit rebuild
front diff ring and pinion only $20
ECU $50
front rotors $30 pair
stock suspension $200

  • 7 months later...
  • 10 months later...

Everything has sold now except suspension.

If you need any further advertising advice, just pm me.

Unless you are pms-ing. Then don't pm me. I don't want our cycles to sync.

Sounds like you're the only one needing advice mate LOL

  • 8 months later...


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...