Jump to content
SAU Community

Recommended Posts

Leverege is the answer!. I presume it's a 1/2 plug where you use the breaker bar or ratchet straight into the plug? If yes, put the breaker bar on it and put and extension onto the breaker bar (piece of pipe). They get overtightened when reinstalled for some reason. They really only need to be firmly tightened not done up like they're holding the whole car together like they seem to be most of the time!

Otherwise you could try a bit of heat (a bit, not glowing red!) around the bung. This will hopefully soften any seallant that's on it and enlarge the housing a little to loosen it as the alloy will expand quicker than the steel plug.

Good luck!

If you can get someone else to maintain the pressure on the breaker bar while it's being heated that will make life easier and you don't over or under heat it. IT will let go as soon as it reaches the right temp. Don't burn him though, he might not come back....

Ok so I jacked it up, and with afew extra inches or leverage and using my foot (nearly doing my back lol) she cracked, you beauty !!

good news :)

I was going to say...be careful with 1/2" extensions/breaker bars etc. Often the plugs are a little round already and you can really f**k it.

You can get 13mm square fittings for this exact job. They are a lot tighter fit and won't round it off. The one I have is 13mm square at one and and 19mm hex at the other so you can put a big spanner or bar over it to get the leverage you need.

But I'll be f**ked if I understand why they are alawys so damn tight! Even when I put them back in a little loose, it takes f**king superman to take them off again!

wouldnt go crazy with the leverage as you might strip the 1/2" socket, tap and heat works for sure

damn straight, good tips.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
×
×
  • Create New...