Jump to content
SAU Community

Recommended Posts

Hey guys,

I moved into a new rental property this week. I chose the place over others specifically because it had a big workshop/garage/carport setup behind the house and secured behind big gates.

Unfortunately, the first night I came home, and learnt that my car has some clearance issues and can't get into the driveway. The driveway doesn't look that offensive, but it's just a combination of rise and falls that makes it really bad for a lower car. Imagine a slippery slide made from concrete, thats how it looks from the side. Car has to come up off the street, clear a crest before going down a ramp, into a slight drainage depression, before levelling out into the parking area.

My car scrapes the exhuast and rear subframe plate on the way up - and then hits the front bar as I reach the drainage channel. Have tried all methods of angles in both forward and reverse, no go.

Car is legal height, only lowered on Tein H-techs (15-20mm lower than stock).

I need help trying to find a solution.

I can't reconcrete, as it's not my house and I can't put a metal plate down to even out the gradient as that part of the driveway is out on the nature strip and subject to council regulations which say I can't put anything out that would obstruct the gutter or walkway.

I'm really after something temporary that I can easily and quickly move under the car to get in and out.

I have used wooden ramps in the past to overcome this problem at another house with another car, but those things tend to shoot out under accelration (especially when i'm reversing up hill) and move around a lot.

Has anyone got any other ideas?

Link to comment
https://www.sau.com.au/forums/topic/419931-low-car-driveway-fail-help/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

I'd love to - I've seen someone has recently released G35 cup kits for about 2k undelivered.

But maybe I should have been more specific and said i need a 'practical and affordable solution'

damn that'd be frustrating. find the perfect house, with the perfect setup. The you realise you can't even get into the driveway lol..

So you can't put anything in the gutter to make it level? that's stupid if so..

planks might be your only option or airbags..

I only just make it in my driveway, going in i scrape the rubber under-front bar sort of thing (idk what it's called) but going down i don't scrape at all and i'm lowered just over an inch..

goodluck!

Yer, i really don't want to leave it on the street overnight. I have had two cars keyed in the past and it's heartbreaking not to mention expensive.

I have seen some 'loading ramps' made from lightweight aluminum that are used to load mini excavators/bobcats etc onto trucks - but they are about $400.....bit exxy.

The other idea I had was to get one of those plastic speed humps you see in car parks - i reckon if i put it in just the right place it might help 'hop' the front bar over that part of the drainage dip. They cost about $70 - and I could probably get that past the council as it's not a trip hazard.

Wouldn't it be just better all round to put it back to stock height and not ruin the car?

that would rank a distant place in terms of options, slightly in front of selling up and buying a 4WD. In order to overcome the obstacle I'd probably have to raise it higher than stock.

i rekon just put down some ramps temporary then get onto the coucil to fix it. i remember reading about some dude on here who did exactl ythat and the council paid due to his car being at legal height

Heres the link to the Phantom Cup Kit group buy.

http://g35driver.com/forums/suspension-vendor/422096-phantom-air-cup-kit-suspension-now-offered-statik-performance.html

The vids of it in action are pretty impressive, nearly 6-inches of lift....couldn't help send him an email to see what it would cost to get a kit to Australia.

that's probably a fair approach.

I'll just play dumb if someone complains.

Those metal sheets are not cheap though - $100's of dollars - and the last time i 'obtained' one I nearly broke my back trying to lift it onto the back of Hilux - they weigh a metric tonne!

Anyone have one laying around or know where I can get one on the cheaps?

gutter/driveway is the first thing i check before i even look at a house....

for the gutter, you could dynabolt a length of 3inch pipe into the recess.... then weld the nuts on so nobody can steal it.

for the hump... no idea. if it was paved you couldve lifted them and levelled the dirt underneath...

for the dip at the bottom, best bet would be to screw together a ramp from lengthways wood and a sheet of marine ply on top... or maybe sleepers with wedge ends... even the alloy ramps would work if you chocked up the centre..

my parents built some houses in the 80's with similar fail driveways.... deep gutter, footpath that angled up, then steep decline driveway to the level garage. the first visitor had a jaguar xjs that got wedged on the hump with all four wheels hanging. funny as.

Need pics of driveway, i used the playground rubber mesh stuff they lay down, its like really hard and great for evening out dips...

was gonna suggest something like this.

seen things like this. one of the houses a few blocks over has these in the gutter

69040_FAM-300x300.jpg

ramp2.jpg

Need pics of driveway, i used the playground rubber mesh stuff they lay down, its like really hard and great for evening out dips...

That's what I'm talkin about! Good idea. Where can i get that stuff from (and don't say my local playground haha). Clark Rubber maybe?

Alex, those things you posted are from a company called Bridgit - they cost like 300USD for a section and weigh 100kgs, imagine the postage! Good suggestion though. Maybe you can check out your neighbors to see if it has a brand?? Might be a local supplier??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...