Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

So... Looks like this will be up and running soon. Booked in for tune on Wednesday (11th).

Spec list as follows, will be interesting to see what it produces.

1994 S1 R33

~165,000 kms, unopened engine

Nistune ECU

GTX3067 w/ 0.82 A/R Garrett internal gate housing

Stock manifolds

Pod filter - Alloy pipe intake

Z32 AFM

Blitz return flow FMIC

Greddy Profec OLED boost controller

Nismo 740cc injectors

Walbro 465 pump

3" Custom stainless exhaust.

Hopefully all the required supporting mods are there to let this turbo do its stuff. Shame I didn't end up getting the 0.63 A/R housing as first thought, but now interested to see what it will do with the 0.82.

So... Looks like this will be up and running soon. Booked in for tune on Wednesday (11th).

Spec list as follows, will be interesting to see what it produces.

  • 1994 S1 R33
  • ~165,000 kms, unopened engine
  • Nistune ECU
  • GTX3067 w/ 0.82 A/R Garrett internal gate housing
  • Stock manifolds
  • Pod filter - Alloy pipe intake
  • Z32 AFM
  • Blitz return flow FMIC
  • Greddy Profec OLED boost controller
  • Nismo 740cc injectors
  • Walbro 465 pump
  • 3" Custom stainless exhaust.

Hopefully all the required supporting mods are there to let this turbo do its stuff. Shame I didn't end up getting the 0.63 A/R housing as first thought, but now interested to see what it will do with the 0.82.

Indeed - me too, it's quite a different setup to really anything else done on here and it may provide an interesting result. I have reservations about the 0.82a/r housing but there are ways it will potentially help it, too.

EDIT: Seems to be a time limit on when I can edit my posts...

For me it will be interesting to see how this compares with previous results of GT3071 with same turbine housing. It seems like GTX turbos flow about the same as next size up GTs, so GT3071 power with bit better response would be nice.

Trying not to get my hopes up too much.

Edited by M@&k

Yeah, don't get too ahead of yourself - though for what it's worth I think the expectations seem pretty realistic. I suspect it should have some hilariously usable power :) Look forward to hearing driving impressions of it when you get it back! Look forward to hear (hopefully) how it goes tomorrow

I have seen one review of a GTX3067R replacing a GT3071R in 0.63 housings and it spooled slightly earlier than the GT3071R .

To be fair these turbos use different compressor housings , T04E 0.50 AR for the 71R and T04B 0.60 AR and port shrouded for the X67R .

A .

Edited by discopotato03

Thats a bummer Mark looking forward to seeing your results :(

My guess is you will see around 250-260kw if your setup has a good exhaust and intake system.

Good luck & looking forward to your driving impressions :)

I think you should of gone the 3071 if you wanted more mate ;)

My car was well sorted and I only went 288kw knocked back to 278kw on around 23psi on quite a low reading dyno with the 3071 and you have 4mm less of compressor so dont know what that will equate to.. Apart from ALOT of fun as I think its gunna be all in around 3500 :)

Edited by Mick_o

You haven't really given much of an impression of how free flowing your exhaust is etc, so I'm going to be different - go out on a limb here and say just over 270rwkw is possible if all goes well - and if boost control isn't lazy and depending on dyno run rate, 1bar in the low 3000rpm range.

Again, all depends on quality of tune and parts, how well the dyno is set up, and how good my crystal ball is haha.

Mick_O's prediction is probably a realistic expectation to set, however - I wouldn't aim higher, I'm just being devil's advocate as I think >270kw is in the realms of possibility.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...