Jump to content
SAU Community

Recommended Posts

  • Replies 119
  • Created
  • Last Reply

Top Posters In This Topic

Well based on that I'm in the 12-15 range then so maybe the scales are OK.

The 10-12 is leaner than me, but I'm leaner than the 15 guy.

Edited by ActionDan

OK after having a proper go at that routine, it took 53mins, including keeping in my previous ab work and the dips because I like those at the end.

The order taken was.

stretch

crunches

squats (as mentioned these are quite hard on my ankle at the moment so only 25kg and only parallel, I also have to have my feet at roughly 45 degrees, further in i go the worse my ankle protests)

bench

SLDL

overhead press

ab work

bb curls

bb rows

bench style dips

Taking 2min breaks, I can see I'll be able to add weight to pretty much everything, but will hold off for now while some back/shoulder/arm twinges go away (from working on the car flat out lately).

I don't get the same pump after a workout as I did, especially in the bicep area, hopefully that will change a bit when i up the weight on a few things as im doing everything fairly light on.

Pump isn't a reflection of a good workout though. It's just a mental thing.

Do weighted chins and see if you get bicep pump.

Also, how are these twinges going away? Just because the pain eases doesn't mean the knotted muscle or impinged nerve does. Get a decent treatment.

Have you thought about doing conventional dead lifts? Or are they another day? Just thinking they will work your ankle a bit driving through the feet

It will change as you up the weights. The other day I set PBs in deadlifts and I struggled bad on barbell curls. Gotta remember that a "pump" does not mean you've worked harder or lifted more.

Recommend sticking crunches and barbell curls at the end too. You did curls before rows, which recruit biceps. Always do the compounds first and finish with isolation...start from the core and work out to the limbs.

Pump isn't a reflection of a good workout though. It's just a mental thing.

Do weighted chins and see if you get bicep pump.

Also, how are these twinges going away? Just because the pain eases doesn't mean the knotted muscle or impinged nerve does. Get a decent treatment.

Have you thought about doing conventional dead lifts? Or are they another day? Just thinking they will work your ankle a bit driving through the feet

Yeah fair point re pump. I'm looking around for a cage with a chin up bar and dip station.

I rub and stretch out twinges myself usually. If an exercise movement is not aggravating it then I've usually done it working on the car etc so it goes away in time when I get a chance to rest.

I'm doing SLs because they were what was listed in starting strength, probably easier on the back too?

The ankle gets plenty of work via squats and 3k walk with some light jogging thrown in each day, the surgeon said it takes a good 12mths to come back from what I didi, it's only been 4.

It will change as you up the weights. The other day I set PBs in deadlifts and I struggled bad on barbell curls. Gotta remember that a "pump" does not mean you've worked harder or lifted more.

Recommend sticking crunches and barbell curls at the end too. You did curls before rows, which recruit biceps. Always do the compounds first and finish with isolation...start from the core and work out to the limbs.

Yeah I can move curls to last easy enough,I thought I was showing some real dedication putting them fairly towards the end and doing squats first lol I've also tried to break it up with push/pull alternating to an extent.

Why move crunches? They help me warm up.

just do all your CAARMING at home instead of at the gym.

Home = gym but what is Caarming?

Yeah I can move curls to last easy enough,I thought I was showing some real dedication putting them fairly towards the end and doing squats first lol I've also tried to break it up with push/pull alternating to an extent.

Why move crunches? They help me warm up.

Have you ever known someone to pull their abs during a workout? You use them every minute of the day, you don't need to warm them up. You do, however, need them for compound exercises...so there's no point wearing them out in isolation...just like biceps. The common theme here is that if you are lifting heavy enough on the compounds, you'll barely be able to do the isolation because the muscle group has already been used.

Good work on alternatIng push and pull...definitely works well for me breaking things up like that. But yeah, compound first, isolation last.

As for the pump, as jangles said it's all mental...as are a lot of your habits like crunches to warm up. Forget that dude who said it, but fitness industry is a breeding ground for OCD behaviour. We get good results and misattribute everything we do towards them, including the pointless shit. Less is sometimes more, it's about working out smarter rather than harder. More important is that you have lifted more weight rather than how faxed you feel or tight your biceps are.

I've never pulled an ab but I've always done ab work. I'm not warming up the abs, just warming up myself.

I never used to put the crunches first, I only started doing it with this routine to switch things up and it helps me get blood flowing and a light sweat going, I can move it anywhere as I couldn't care less when/where I do it, I just don't like to start out with a heavy motion straight off the bat.

you don't know what CAARMING is?

youtube - Arnie the pump

Also - SLDL is not in starting strength. the program listed on the earlier pages is not from starting strength.

edit - seems all your injuries/twinges etc come from that anchor you call a motor.

Fit a VH45 and win at life.

Edited by TTT

I've never pulled an ab but I've always done ab work. I'm not warming up the abs, just warming up myself.

I never used to put the crunches first, I only started doing it with this routine to switch things up and it helps me get blood flowing and a light sweat going, I can move it anywhere as I couldn't care less when/where I do it, I just don't like to start out with a heavy motion straight off the bat.

Bad luck. Start out with a compound movement. That's what warm up sets are for. Your crunches are doing nothing but costing you good lifts, so stick them at the end. I stretch my arms and then it's straight into an 85kg bench for 10 reps. What makes me better than you, captain crunch?

Warm up sets arguably cost good lifts too...

I'm surprised, I thought you guys would be into warming up, good way to avoid injury which is why i do it now, that and being 30 means I'm not as injury resistant as I used to be.

Edited by ActionDan

Haven't trained abs in years cause I know squatting uses your core like a motherf**ker. Good thing is most compound movements will work your core since that area is for stability.

The program listed is something Markos put together for beginners to lifting.

Starting Strength has even less volume and therefore less pump so you'd go crazy.

Edit - doing crunches is not a warm up for any exercise.

how would doing multiple bending of the middle be a warm up for anything you will use during any of the exercises listed in the program?

Edited by TTT

Warm up sets arguably cost good lifts too...

I'm surprised, I thought you guys would be into warming up, good way to avoid injury which is why i do it now, that and being 30 means I'm not as injury resistant as I used to be.

We do warm up, with warm up sets.

Can you explain how crunches are going to stop a shoulder injury from bench or a leg injury in deads and squats? If anything they are more likely to cause injury, because you are weakening your core before doing big lifts. You need to have a tight core during squats and deads else you can end up with injury when you're going heavy. Warm up by doing the exercise lightly...you're not going to hurt anything by doing this.

It's like I said in my previous post, there's a whole heap of stuff you're misattributing to success...need to break the mental barriers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...