Jump to content
SAU Community

Recommended Posts

Hey guys,

First post on the forums so i'm hoping this is in the right section.

I'm a proud owner of an R34 25GT, fresh imported, full complianced. Havn't had any problems with it until now.
When imported it had approx 67,000k's clocked up so i thought i'd leave i until around 70,000 before getting a major service. Just after hitting 70,000, check enigne light starting appearing periodically, an ignition restart would remove the light so i didn't think much of it.Took it in for a major service and the mechanic shits bricks when he sees the condition of the timing belt (I saw this also, didn't look as bad as he was making out but i figured i'd get it replaced to be on the safe side). So after forking out $800 for a full service and timing kit i get my car back on the weekend and i'm less than impressed with the outcome.

Firstly, check engine light is still showing, being more persistent now than ever.
Secondly, in the low RPM range car has lost a substantial amount of power.
Thirdly, the note the exhaust is making is not what i remember at all, when driving every now and then it starts grumbling like a V8 with no exhaust.

All this is making me question the condition of the coilpacks. I took the car back to the mechanic who ran it on the computer and got an error code advising that the coilpack(s) were faulty.

I'm really beginning to question the integrity of this mechanic as he claims he cannot diagnose which coilpack is faulty so we have to replace them all and he quoted approx $320 for the parts + labour on top.
Now this sounds like absolute shit to me so i did a little research and it seems coilpacks can be tested using a multimeter? Can anyone confirm this?

Normally wouldn't care too much about the pricing but i know when i'm being shafted and i;m not keen to give this guy any more business. Can anyone either recommend a mechanic in the northern suburbs of Melbourne or is the job simple enough that i may be able to do this myself?

Cheers,
Vexx.

Sounds like a coilpack issue, if you definitly notice a change in power and exhaust note youve probably dropped a cylinder. If the car idles rough like its not running on all cylinders u can check which coilpack is faulty by disconnecting each coilpack. If the engine changes note again then that coilpack is fine but when u un plug one and there is no change that will be the triublemsome coilpack.

Make sure u do an ecu diagnostic to tell u which fault codes come up. If it IS a coilpack issue you will have code 21.

What is making you lean towards a timing issue BuuBox?

Would timing issues be bringing up the engine light?

Also just thought i might add, she's starting to chug the petrol pretty hard lately - Another sign of a bad coilpack?

Thanks for the info there RB25DETC33, might have to give that method a try on the weekend and see how i go. =]

What is making you lean towards a timing issue BuuBox?

Would timing issues be bringing up the engine light?

Also just thought i might add, she's starting to chug the petrol pretty hard lately - Another sign of a bad coilpack?

Thanks for the info there RB25DETC33, might have to give that method a try on the weekend and see how i go. =]

It could well be a timing issue... Since the mechanic has done the timing belt, he may not have aligned the cams up with the timing marks, one of the cams may slightly be advanced or retarded throwing out your combustion timing.

But do an ecu check first. eliminate things that the ecu can tell you.

  • 2 weeks later...

So a little update here.

Took my car to a different mechanic for a second opinion.
This bloke said it's possible that coilpacks are shitty but he said the cam timing seems a bit off.

Went back to original mechanic who did the job and he conceded it was a little bit off, corrected it (Free of charge of course) and then ran some scans to find an error code for the CEL.
Codes came up as :

21 - P1320 IGN SIGNAL-PRIMARY

Bloke reckons i should replace all 6 coilpacks, he doesn't seem to think it would be worth trying to isolate which pack is failing.

Would it be wise to just replace all or should i attempt to isolate?

Any suggestions for which packs to go for? OEM or Splitfires?

Cheers,
Vexx.

if i was you i would replace all six coil packs then you wont have to worry about them for a long time. . choice of brand seems to be a personal thing on this forum so you will get a few different opinions on that

  • 6 months later...

I've been getting the same problem recently (R34GTT) - inconsistent misfire and farting only under WOT at 16-18psi and close to redline, a lot of the time it doesnt happen but 20-30% of the time it does. Took out and inspected my Yellow Jackets (less than 2yrs old) and copper spark plugs NGK BCP7RES gapped at 0.8mm (done only like 2000kms) - the plugs look new - no soot or signs of running rich -just the thin lower thread strip is black, coilpacks look new, no hairline cracks etc,. No visible oil/fuel in cylinders/ spark plugs.

Multimeter tests consistent resistance throughout coilpacks, and idle tests by removing coilpack connections one by one changes the engine note throughout so all coilpacks seem to be good here. But obviously under WOT it starts misfiring n farting. I didnt take out n inspect my 4th coilpack/spark plug as its under the J pipe and I couldnt be farked removing all that crap. But pretty sure its the same as others / good cond. Did take out connector under idle and it changed engine note so it seems ok.

Check engine light came on after coilpack inspection - paperclip test/clear codes and reset ecu (remove battery terminals n drain charge) didn't remove it - only threw out one error code which was the boost sensor. How do I get rid of this light?

The last couple days after removing coilpacks/plugs I get no power n torque from 1000-2000rpms but after that its normal and hammers hard under boost to redline bar the ocassional misfire/brickwall. Esp on a hill from stop to go I get inconsistent no power till 2000rpms. Is this a timing issue?? Wasnt happening before. Checked all connections of coilpacks/plugs all firm n good. Please help.

cheers

Edited by rondofj

I dont know about the plug gap, JEM had fitted new sparkies and set it at 0.8mm and it ran fine for 4 months till now, I'm thinking it could be the bloody afm, maybe a solder joint or something, its weird, upon first startup and driving for the initial 5-10 mins theres just NO power between 1000-2000rpms then its normal after that rpm band. Driving a bit over 10mins after its warmed up, some/not all power comes back, so could it be the thermostat or temp sensor?

My car does something similar, it runs rough when cold then all of a sudden after about 5 minutes it runs fine. Even weirder, when I first start it up it's fine, the issue kicks in about a minute after. I'm placing my bet on AFMs.

took out Z32 afm, soldered all 4 joints and put it back together no difference - initial startup and first 5-10 mins of driving theres NO power from 1000-1800rpms for 2-3 seconds then it jerks a bit then power comes back lol. Fuel filter clogged? It doesnt happen when engines warm.

  • 1 month later...

Hey mate did you ever fix the check engine light problem having the exact same thing happen to me

Took it in for a service they said all was fine turned it on next morning and the same thing

Did you ever find turning off and on fixed the problem ?

  • 3 weeks later...

Hey mate,

Sorry for the lack of replies here guys.

Fixed the problem.

New set of YellowJacket coilpacks instantly fixed the engine light, stopped the exhaust note sounding like a beast WRX and gave me a noticeably quicker vehicle. =]

PS. Yes, turning off ignition and flicking it back over did remove the engine light.. for a few minutes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • jeebus. glad you weren't under it while performing the stunt. Also thanks for the link to the wheel measurer, exactly what I needed
    • In the older stuff there were very significant differences 2wd to 4wd, for example Stagea had strut front end for 2wd and double wishbone for 4wd so it was not minor to swap. From poking around the 2wd v37, it *looks* like it might be more possible; some of the parts specifically have "2wd" stamped on them which suggests the platforms are more similar. You'd still want to start with a 4wd half cut to swap stuff from though. I'd suggest if you don't have a tune on the ECU you don't really need one on the trans either. Throttle mapping is in the ECU side (and you can always use a Roar Pedal if you want the throttle to actually respond to your foot), and really if you are happy with the stock power you probably accept the stock trans behaviour too....its all made to be "sporty" not racey.
    • So, updates. I have not washed the car since it came back from Tassie. I've driven it around a bit but not got around to actually sorting it out. I DID raise it because I cracked the rear bar leaving a hotel which was very distressing. Interestingly, the car drives more compliant now that it's raised a fair bit (5mm front, 15mm rear). Also noticed that my FR height was 10mm lower than FL. So that's now sorted out, too. I also bought this and had it printed: https://www.etsy.com/au/listing/1576422240/wheel-and-tire-fitment-tool-universal?ref=shop_home_feat_1&dd=1&logging_key=08f604d9fa4cc383550ba985e6ac85cd5cac7fbb%3A1576422240 Now, if I was smart I would have taken my brake calipers off to actually use this correctly but it was evident enough to me that in the region where the caliper was... there was nothing to hit suspension/guard/arm wise. So I'm going with "it'll be fine" after using the tool to hopefully very precisely measure the wheel clearance. Also while doing this, I had the very VERY bad idea of jacking one of the wheels/suspension arms up while the rest of the car was on jack stands. I did this to see how the arm would travel. This all was well and good until the car slid off the stands and went through a fence. So don't do that. Incredibly nobody was hurt and there was only minor damage to the rear bumper as the car didn't have far to slide, and had 3-4 wheels on it. The only damage turned out to be the fence itself which was easy to fix, and a little bit of damage to the fibreglass rear bumper trim. I had already planned to try a touch up paint kit to fix the time I drove into my garage door to see if it'd help in the interim before I get it fixed properly. I used the Dr Colorchip kit after looking online and seeing everyone talking about it. Yes it's made for chips and not huge broken missing pieces and I'll be 500% recommending it for stone chips after using it for stupid things like me. This took about ... 10 minutes and looking at the half assed photo the 30 second job I did on the bumper corner was almost perfect just by using the tiny little brush and painting it in. The sealact stuff to remove over-painting is really useful, so if/when I do it again I'll likely slather the touch up paint well over it and then clean it up with the cleaning solution. The wheels should arrive in a couple of weeks. I am still kinda confident after doing a stupid amount of measuring (and borrowing a set of 18x10.5+15) that they will not fit because I overlooked something, somehow and flew too close to the sun. ALSO R34 GTR guard liners do not fit on a GTT. I bought the undertray brake duct guides and had the wonderful problem of them not fitting my intake, my oil cooler and the liners themselves were even worse. Attempting to fit them won't work in general - You would have to cut them up as another poster mentioned as the bodywork is different on the GTT. At least I can try to resell them. So instead of cutting those up, I cut up my old already-cut-up GTT liners and extended them by using some PP plastic and drilling some 8mm holes for some nissan clips for the 'extra' bit. Because I was happy to cut them I was able to mount them pretty damn forward so I now have some semblance of guard liners, and the brake vents seal the bumper from the bottom. It sort-of-looks like this, to give some idea - If you look at the GTR and then the GTT this is when I realised that I needed to seriously measure as the inside of the rim area is entirely, entirely, entirely different and could not take any internet measurements for granted.   
    • If you are Ecutek tuned then these TCU tunes are anywhere from $550 to $700 usd. If you are not ECUTEK tuned, then it gets costly!    
    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
×
×
  • Create New...