Jump to content
SAU Community

Recommended Posts

Not the best with the electrical side of things but sounds like you should get a new relay and try that they're only $15-$20 for a 30amp horn relay. It should be normally open which means no circuit until the switching wire(from the ECU) triggers it to form the circuit. hook it up the way it's been explained and that'll tell you whether thats the problem. It's now a process of elimintaion so write a list of things to check and cross each one off when you've checked it.

this is what I did in my skyline

scrap all the standard fuel pump wiring and start from scratch go to jaycar (car electronics place) get a 5 pin horn relay, 30amp in line fuse, 25amp positive and negative wire(black and red I only needed a meter of each my battery is in the boot you'll need maybe 5or6 red cable and a meter black) and just tools for the job solder and iron ect

run a wire (25amp red) from the battery (positive) and put the inline 30amp fuse along the way somewhere then conect this wire to pin 30

pin 85 earth out to the body(or negitive on the battery)

pin 86 conect to an ignition only source (key barell, head deck ect)

pin 87 straight to fuel pump positive connection

negitive connection on pump you can ground it out to same place as the relay

this is basically the setup I'm running with a walbro and 2 044 they switch and run beautiful hope this helps

Ok cheers for the info, sounds like this is the way to go. Fingers crossed it solves my problem... cars huh :P

and when you get the relay ask for a wiring harness for it makes it a lot easier it cost me about $50 all up including a new soldering iron. car are a love and hate relationship

this is what I did in my skyline

scrap all the standard fuel pump wiring and start from scratch go to jaycar (car electronics place) get a 5 pin horn relay, 30amp in line fuse, 25amp positive and negative wire(black and red I only needed a meter of each my battery is in the boot you'll need maybe 5or6 red cable and a meter black) and just tools for the job solder and iron ect

run a wire (25amp red) from the battery (positive) and put the inline 30amp fuse along the way somewhere then conect this wire to pin 30

pin 85 earth out to the body(or negitive on the battery)

pin 86 conect to an ignition only source (key barell, head deck ect)

pin 87 straight to fuel pump positive connection

negitive connection on pump you can ground it out to same place as the relay

this is basically the setup I'm running with a walbro and 2 044 they switch and run beautiful hope this helps

yeah thats what im thinking...just hardwire it from scratch...

Correct me if im wrong BUT doesnt blue smoke generally indicate the engine burning excessive oil or oil entering your exhaust e.g blown turbo

Correct.. being second hand I have no idea what condition the turbo/engine is in.. is on the cards to inspect inside

Edited by GTS 221

that's the love of cars mate you need to research look up stuff on google go to the local mechanic shop ask questions. I'm a bricklayer by trade and now try to go everything on my cars even tort myself to aliminium weld to get stuff done. my advise try it yourself if you stuff up you will learn by your mistakes

A quick check of the Commo wiring diagram shows its fuel pump relay is a positive trigger from the ecu, Skyline (pin 18) is negative.

Multi meter will soon sort out the problem and another relay.

Commo also has the oil pressure switch fuel pump safety cut out, so that circuitry should also be investigated.

If you want a legal and safe conversion, you never run a fuel pump without some sort of safety cut out.

85 connect to ign 12v switched

86 connect to pin 18 on the ECU header or ECU fuel pump output

30 is a fused power supply from the battery

87 is wired to the positive side of the pump

This is the correct safe way of doing it.

Edited by RRob

Correct.. being second hand I have no idea what condition the turbo/engine is in.. is on the cards to inspect inside

Are you from Melbourne/did you buy the original RB/VP from a guy from Sydney? If so the car belonged to someone I knew, and wasn't treated very best. Ran on 5 cylinders a lot (bad AFM), never serviced, etc. After the car was written off, he did a few burnouts on the lawn (cold motor). Not trying to upset anyone, but yeah. Worth putting new rings and bearings in at least.

And for the haters - fantastic sleeper. Boring white VP commodore combined with ZUTUTU. I wouldn't do it myself, but it sorta opened my eyes...

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...