Jump to content
SAU Community

Recommended Posts

Sierra stage 1 turbo

Scotty dump

Scotty 3" front pipe

Nismo exhaust

Plenum spacer

Scotty actuator mod

Hdi front mount

Transgo shift kit

Turbosmart boost t

I do have a nismo ecu but it isn't fitted as it was running to rich. It will be waiting till I have money to do my emanage

Think thats it haha

sh###t you be running 13eents easy, while i hope for a 14 flat

my mods

dump pipe

custom 3" exaust

shift kit

custom intake pipe

14.1 with these mods 1.9 60 foot

I'm really hoping so. I need a new BOV so hoping that doesn't effect me to much, its bleeding off a bit up high. Also really need an intake pipe to get the most out of my setup. But we will see how we go.

Well not exactly what I had hoped for, 14.02 @161km/h I hit boost cut twice on tgis run. So it should have been a 13 easy. I had boost wound down as low as possible so not sure what to do next. Every other run hit cut a bunch more times so was much slower.

  • 2 weeks later...

Took the car to Hiddenvalley last night, managed a 13.6 at 102 so still doing the same mph, couldn't get my 60 foot under a 2 seconds, very very slippery! They just had scrapped the rubber of and re layed vht hopefully when they get more rubber down it will be better! Plus side I've managed to get my reaction down to .006 so managed to do a number of .406 reactions

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...