Jump to content
SAU Community

R33 Stock Bov Flutter Sound - Whaddaya Reckon Of This?


Recommended Posts

Techinically its not legal as its making noise.... You will soon get over it as it will get old quickly!

This will not get the bishes moist!

  • Like 1

To your dignity.... yes....

There are SO many topics on SAU about BOV's and not running them, blanking them etc............

My understanding is that you could bend your turbo blades. By Blocking off the BOV the built up pressure that normally gets released to atmosphere or recirculated, has nowhere to go but back though your turbo and as such temporarily stalls the compressor, which can bend or brake the blades, and the stalling of the compressor is what gives the flutter sound.

  • 3 weeks later...
  • 1 month later...

Lawl! These threads always deliver!

But the whole flutter thing will soon be annoying for a daily drive!

AND you can get EPA's based on it anyway as its still creating a sound!!

In other words, DONT DO IT!

You f*#@Kin idiots..... The 'flutter' sound is called compressor surge. it is NO GOOD for your compressor blades, it slows down your turbo from spooling in between gears and in worst cases, f*#ks up your compressor blades.

Sometimes when people get too ambitious with sizing their aftermarket turbo and get the housing sizes wrong, or over fueling at idle because they didn't reconfigure their fuel map properly after they fit a bigger turbo, compressor surge OR 'flutter' is the result.

The whole purpose of having a BOV is to release the excess boost so it doesnt slow down your turbo in between gears.....its for response.....WTF would you sacrifice response for a sound ?????? fu*kin idiots

Man, I really wish these kids learn about the fundamentals of engine mechanics before they make a total dick of themselves or worse, totally ruin their cars.

Edited by NATAS

You f*#@Kin idiots..... The 'flutter' sound is called compressor surge. it is NO GOOD for your compressor blades, it slows down your turbo from spooling in between gears and in worst cases, f*#ks up your compressor blades.

The whole purpose of having a BOV is to release the excess boost so it doesnt slow down your turbo in between gears.....its for response.....WTF would you sacrifice response for a sound ?????? fu*kin idiot.

You sir are a f**kwit

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...