Jump to content
SAU Community

Recommended Posts

As long as you have safety bars in place at the right height, you're not going to break your neck. The body tips over forward and you end up on your knees with the safety bars taking the load, before this happens.

If you feel like this, you need to tilt the head up higher, chest out further and shoulders back further.

yeah I used to get that a bit until I started really using my rear end to power up, and stopped wearing heeled shoes

I wear powerlifting shoes, so maybe I need to focus on using my rear to power up as you say if I start squatting again.

I wear powerlifting shoes, so maybe I need to focus on using my rear to power up as you say if I start squatting again.

If you are tipping forward when coming up, it means that your hip/rear is already rising faster than you can handle.

you either lack upper back strength or need to practice squatting more upright.

Front squats are good for this.

If you are tipping forward when coming up, it means that your hip/rear is already rising faster than you can handle.

you either lack upper back strength or need to practice squatting more upright.

Front squats are good for this.

I tried to do front squats as I cant back squat due to my injury but I couldn't even front squat the bar. Can't seem to get any upper body strength going on.

Sorry I didn't know you had an injury.

Why couldn't you squat just the bar? too heavy or injury related? mobility?

yeah too heavy, I just couldn't get the mechanics of balancing the bar in front of me.. yet I was back squatting 65kg

You should easily be able to front squat the bar. Keep your head and elbows high.

Just try bw with a broomstick til you get comfortable doing it

Edit: TTT suggested broomstick as well, great minds think a like

Crossed arms sucks, I prefer the other way

Edited by Mitcho_7

Yeah tipping forward. Birds would be able to explain it better than me

Only seen you attempt it once and I forget where the point of failure was.

I'm not very good at front squats myself...arms don't quite have the flexibility for it yet.

I actually find front squat positioning/mechanics much easier to get good depth but obviously cant do as much weight.

Keeping your elbows high and head up are really the only cues I use. As soon as the elbows drop its about 20x harder I find

Edited by Mitcho_7

my injury is between L5 and S1 so even though I wear a belt it, I can't get it low enough to support that area. It's right down at the top of my glutes.

what TTT said about falling forward is really good advice. It took me a long time to learn how to sit back into a squat and use my glutes instead of shifting my weight forward and using my quads.

I was a lot stronger squatting from my quads in the beginning. Any time I felt the weight get heavy I was shifting weight onto my toes. Wasn't helped by the oly shoes I was wearing. This was until I started having crippling knee pain. Its was so bad I was hobbling around and couldn't sit for long periods without them aching.

So I ditched the oly shoes and practiced sitting back, having the weight on my heels. I would actually lift my toes off the floor as I squatted to make sure I didn't come forward. Later I also switched to a low bar position which also helped and I do a lot of front squatting as assistance. Very difficult to not sit back when front squatting as TTT suggests.

This fixed my knee pain but makes it really hard to buy pants/shorts as my ass is heaps bigger! lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...