Jump to content
SAU Community

Recommended Posts

Geez your a rude bastard Pete, 3 wide and every bastard can get the f**kk out of the way.

See what i mean buddy,,,natsoft lied again hey,,,no way would a 2wd car beat a 4wd or is that twice you have been owned ?.

Love and kisses as always

Neil.

You need to re edit the broken down video so i can see myself finally passing you. You cut it as my 32 comes into the mirror haha. I know why check out the passenger foot well on both videos. Your haltech control unit plate comes loose and is dallying around in the footwell

Look, that will be enough of this gtr love-in crap. Rubish cars driven by rubish drivers. Was that another 2wd coming home in 3rd,,,nice work Mr Milano and a VERY big congrats to Mr Wootten.

Pete, I don't know if you are awhere but there is a "Secret GTR owners club", and in there constitution rule 7 subclause 8a it states that if a GTR owner gets beat 3 times by rear drive Skylines then the club will remove the car from said owner. Tread carefully buddy you are on your last chance.

HA HA

Neil.

  • Like 2
  • 4 weeks later...
  • 2 weeks later...

Yea if your read the Internet the world will end with a stock oil pump

Shame the Internet is full of f**k stains that drag race..... I don't drag race

Ps if I was building a engine I would use a flashy pump

It's only the engine that have had the Nissan let out that need new flashy pumps

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...