Jump to content
SAU Community

Recommended Posts

2 challenges in one month.

Challenge the first..

Body weight on the bar, squat till you can squat no more.

high bar, low bar, whatever..

each squat must break parallel (which means your hip crease when you bend, must be below the top of your knee at the bottom of each rep)

if you want to go Ass to Grass then go for it.

Challenge the next

Body weight x 1.5 on the bar, everything else the same.

Video from side so people can see depth.

Don't hurt yourself

Don't dodge this challenge.. at least do one of them.

If you can't squat your own bodyweight on your shoulders... STOP EVERYTHING!!!!

Put down your iPhone

Put down your designer microfibre towel

Walk over to the squat racks and squat the bar many time.

Add 5kg each side. place bar on upper back and squat many times

Continue doing this until you need to lie down for a while.

then lie down

then get up

then do 4 more sets.

Pick up your iPhone, micro fibre towel, your bottles of pre and intra workout drinks, full up your post work out drink bottle and drink it.

get home and eat many many animals and stuff animals eat.

go back in 2 days time and do it again.

repeat for 3 months.

Link to comment
https://www.sau.com.au/forums/topic/422759-squats-the-challenge/
Share on other sites

  • Replies 82
  • Created
  • Last Reply

Top Posters In This Topic

challenge for the ladies? I don't know many girls who can squat their own body weight for reps

Really? I thought you trained at Elite Physique in Canberra. I saw 15 do it there at the last comp, only a handful were PL'ers, most were Crossfitters or physique competitors, a few went 2 x bw

Canberra has some very strong girls

might give this ago.

dont expect i'll get many reps out compared to others here but hey we will see. Weighed in at 67kg so I'll attempt at 70kg cause i'm a big kent like that.

not sure how to upload the video either

Birds - stay up top to breath out and in, then down.... towards the end you might need to stay up top a little longer to take 3 or 4 breaths so do it if you want.

Do what you think is right instead of looking for ways to cheat.. lol

I'd say your hands/shoulders and lower back will be fried before your legs give up anyway so resting in standing position to wards the end will be hard anyway.

FIGJAM - upload vid to youtube

link it here.

Really? I thought you trained at Elite Physique in Canberra. I saw 15 do it there at the last comp, only a handful were PL'ers, most were Crossfitters or physique competitors, a few went 2 x bw

Canberra has some very strong girls

Nah mate I train at Anytime Fitness haha, commercial gym in all its glory!

I'm more speaking for the girls on here.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...