Jump to content
SAU Community

Recommended Posts

I'm in the process of rebuilding my 25. Just looking at my VCT oil feed, I stuck a pick into it and it only went in a max of 2mm deep. Is this normal, does the oil feed straight up into the gallery from the bottom of the block or does it 45deg into it?

Hopefully this makes sense, I want to make its not blocked because VCT wasn't working when the motor was last running.

post-84181-0-92728400-1367539826_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/424564-rb25-vct-oil-feed/
Share on other sites

Think it works as a check valve so might just be bottoming out the check valve. Just blow some air through and see if you can feel it come out. If the engine is out that is. I think if you blow air into one of the ports where the filter goes and block the other 2 head feeds with your fingers then you should feel some air come out

  • 2 weeks later...

So I drilled feed with the top of the block facing down (I used a bit smaller than the hole size so it didn't cut any metal) and some oil dried up like jelly came out. The feed seems free now and I can get a pick in there but compressed air still doesn't come out of the feed.

I've tried blow air through various spots including both oil filter ports and the oil pump port but i get nothing from the front VCT feed!

Hi Guys,

Does anyone know where in the oil system does the VCT feed, feed oil from? i.e where does the feed tap into the rest of the system? if possible could you highlight it on a photo for me? Its hard for to now that the engine is partially built.

Yeah should be from the same feed as to the other head oil feeds.

oil pump --> Filter ---> main oil gallery ----> Head feeds

From memory anyway, I did sus it out when I had a bare block and some air and some cleaner spraying through it

can you track down a pic of the oil feed? if you can get a hold of a manual it will show it

I have the Nissan workshop manual but it doesn't detail the oil flow /path it just shows how to assemble oil pump etc.

Here's a photo of it

post-84181-0-96909000-1369099208_thumb.jpg

I got this from the oil control thread its for an RB26 though

post-84181-0-19310900-1369099313_thumb.jpg

How do you guys troubleshoot a blocked oil gallery - with drilling as a last resort as the block as it has already been cleaned and assembled...

  • 4 years later...
14 minutes ago, silencium said:

Sorry for digging up this old thread but I have kind of a similar problem.

Does anyone know if there is a check valve in the VCT oil feed or if it simply is a restrictor?

Thanks for the help

 

Why would there be a check valve?

How would that be useful?

Why do you think there is one?

why does it matter?

 

I vote my ass no check valve

That is very simple: When the engine is stopped, oil could flow back due to gravity, leaving air in the oil gallery. Next time the car gets started the air has to go out through the journal bearing before the oil follows.

I do not know how much the oil actually flows back, but it is definitely a bit, because otherwise oil pressure would be instant on the first engine cranks during start up. But it usually takes about one second till the oil pressure switch goes off.

Using a check valves in the block would make sense imho.

If one has a RB block laying around it could be checked with a thin wire.

Edited by silencium
typo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...