Jump to content
SAU Community

Recommended Posts

Hi everyone,

Having noticed some members having trouble with this paint application, I thought I would show you guys how to get that nice wrinkle finish paint look without spending an arm or a leg or paying someone else to do it!

First up we are going to need the following key tools and chemicals:

1. some paint stripper IMG_0625_zpsa431012f.jpg

how much is up to you but always good to get more - this is $50 (4Ltr) worth of paint stripper sourced from AutoBarn (price varies amongst size)

2. some prep wash / grease remover - cost is approx $12IMG_1888_zps6ddfdd4f.jpg

I SWEAR BY THIS!!! :worship: and is a must have to ensure that all dirt and grease is removed on object before painting (also good at taking tar off your guards)

3. the paint

IMG_1890_zps765d5af6.jpg

VHT wrinkle plus - BLACK wrinkle finish spray paint can - you can get this from your local Autobarn store $18-$25 per can

4. a heat gun

IMG_1889_zps19adc221.jpg

although not obligatory I find that using a heat gun you get the best wrinkle finish - if you don't have one get one or borrow one, it really pays dividends with the end result

5. some masking tape

IMG_1891_zpsf0835da5.jpg

essential to tape off all the bits that you don't want paint to get to

additional things to have are lots of paper towels :yes:

OK, so now we need an object - I thought I would start with this....

DSC00667_zps6581d730.jpg

RB26 timing cover - which is a pretty good example for this tutorial IMO note - this is not from my Tomei engine and was from my old engine :turned: )

After applying several coats of paint stripper and rinsing it now looks like this (no sanding required)

IMG_1886_zps8a0b4f1c.jpg

This was the longest part of the job but necessary

IMG_1887_zpsffffdaab.jpg

then apply some prep wash with some paper towels on the object to ensure its all free from dirt, dust, grease etc....

next up, tape everything you don't want paint to get on

IMG_1893_zps1c8954f5.jpg

I thought I would go a step further today (the red over spray is from me previously painting this in red wrinkle finish - the things I do these days :nyaanyaa:)

IMG_1892_zps3111e106.jpg

and also detail the RB26 logo

now we are ready to paint :laugh:

rigorously shake the VHT spray can (for a good minute), the after that

:excl: this step very is important - apply a thick coat in crosspatch pattern as follows:

1st Coat - Horizontally

2nd Coat - Vertically

3rd Coat - Diagonally

IMG_1894_zpsdc79a124.jpg

to start off with it will look glossy like above, but don't stress

:excl: this is another important key step - make sure you plug the heat gun and pre-heat it - so when you have applied the paint it is ready to go

IMG_1895_zps127257bf.jpg

I initially set it at 220deg C but this will depend on the current temperature at the time and being winter here in sunny Qld :dry: I actually had to set it to 250deg today to get the paint to wrinkle (but must me above 200deg c regardless)

IMG_1896_zps0fc53512.jpg

now continuously put the heat gun (very close) around the object until you see the paint starting to wrinkle (this will take some time until you see this happening as the paint needs to set (kind of hardened) but just be patient)

IMG_1897_zpsb5d2b06d.jpg

after you have wrinkled the paint it should look like above - but do not stop using your heat gun and still heat the object at 200deg for a good 5-10mins. This process will partly-cure the paint

IMG_1898_zps85a52b0e.jpg

IMG_1901_zps633aa1fb.jpg

IMG_1902_zps1d998255.jpg

here you can see the wrinkle finish - there is a little bit of over-spray but it gives it some character

IMG_1905_zpsa152f815.jpg

next gently take off the masking tape around the RB26 logo

IMG_1906_zpsf93d1702.jpg

you can wipe and clean off the paint with some prep wash on the RB26 logo

IMG_1904_zpseb19c611.jpg

IMG_1907_zps7c8f3ded.jpg

and there it is - another job done :miner:

This paint take a real long time to dry and get really hard - so make sure you keep it under shelter in a dry place and away from humidity

I did all this today (took a few hours) - and just like everything else, the key to success is preparation, having the right tools and having some positive determination :merli:

Hope this sheds some light to everyone applying this type of paint

cheers,

Ants

Edited by Ants
  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/426649-vht-wrinkle-plus-doing-it-right/
Share on other sites

first of all you ahve a heat gun with temperature settings :woot: fancy basterd...lol

looks pretty schmick mate...have done this to my cam cover and plug cover it can be a pain to get it right...

in the end i settle for good enough..flat surfaces arent too bad but curvy ones are tricky..

another tip if you want, with raised lettering another way to do it is to simply spray it then get a sanding block afterwards and just sand the lettering...well thats how I usually do it anyway ..

looks good :thumbsup:

Haha "Having noticed some members having trouble with this paint application"

I am definitely a victim of this!

Beautiful execution mate, funnily I've actually found the opposite to work well for me for some reason.

I've done light coats on the lower timing cover and have had what I think to be better results.

I find that I can better limit the amount of over spray.

And you're right, heat guns are essential, hairdryers simply don't cut it..especially in the current cold Melbourne weather.

yeah the problem is as you can see in his pics, the flat surface will be ok but thickness on the sides tends to drag it down and leave you with small ripples like this below..it drove me nuts a few times then i went bugger it she'll be right and left it...nobody notices once its on the car

another trick i was told if painting metal is to actually get the metal hot before application as well..I left mine sit on front of a heater for a while...



IMG_1898_zps85a52b0e.jpg



Durable? I've been wanting to re-do my cam covers, and was wondering will it "chip" when working around the motor (plug change etc)

Looks good.

yeah its tough a guts mate...I've hit mine a few times and it doesn't scratch easily...

first of all you ahve a heat gun with temperature settings :woot: fancy basterd...lol

looks pretty schmick mate...have done this to my cam cover and plug cover it can be a pain to get it right...

in the end i settle for good enough..flat surfaces arent too bad but curvy ones are tricky..

another tip if you want, with raised lettering another way to do it is to simply spray it then get a sanding block afterwards and just sand the lettering...well thats how I usually do it anyway ..

looks good :thumbsup:

A praise from the the almighty Artz. thanks mate. It is tricky on concave objects but not impossible (see below)

Durable? I've been wanting to re-do my cam covers, and was wondering will it "chip" when working around the motor (plug change etc)

Looks good.

yes very tough and great quality - but only if done correctly i.e. follow steps mentioned above

Haha "Having noticed some members having trouble with this paint application"

I am definitely a victim of this!

Beautiful execution mate, funnily I've actually found the opposite to work well for me for some reason.

I've done light coats on the lower timing cover and have had what I think to be better results.

I find that I can better limit the amount of over spray.

And you're right, heat guns are essential, hairdryers simply don't cut it..especially in the current cold Melbourne weather.

I wasn't single-ling you mate but merely something I was wanting to post for quiet some time. I am pleased to hear that you have found another method that works for you.

yeah the problem is as you can see in his pics, the flat surface will be ok but thickness on the sides tends to drag it down and leave you with small ripples like this below..it drove me nuts a few times then i went bugger it she'll be right and left it...nobody notices once its on the car

another trick i was told if painting metal is to actually get the metal hot before application as well..I left mine sit on front of a heater for a while...

although Artz is accurate by saying flat surfaces are easier than side surfaces it is not impossible.

A few months ago I painted my Nismo plenum in black VHT Wrinkle Plus paint and it was simply a matter of following steps mentioned above but doing top side first and then doing the bottom afterwords

IMG_1416_zps9b2de319.jpg

IMG_1421_zps17b36efc.jpg

IMG_1424_zpse91e6e81.jpg

no sagging here :no:

IMG_1793_zps2f7b0cf0.jpg

picture of the Nismo plenum with Tomei Advance Spec Engine ;)

cheers,

Ants

Edited by Ants

I wasn't single-ling you mate but merely something I was wanting to post for quiet some time. I am pleased to hear that you have found another method that works for you.

Sorry, I did not mean to sound like I was whinging, just realised that it could have sounded that way over the internet.

I suppose everyone's definition of "thick coat" is different which is where it makes it difficult to judge how much to spray.

Btw if you don't mind me asking, what is that bracket that sits behind the oil pump for? (gold one on the very bottom) I dont quite remember mine having something like that

Edited by RB2600
  • 2 weeks later...

Has anyone tried this on their break calipers?? or do they get to hot to even both i know its only rated to 350 degree or something like that..

car wont be used for track work or anything either i think it would be a nice finish on them

any advice would be good

Sorry, I did not mean to sound like I was whinging, just realised that it could have sounded that way over the internet.

I suppose everyone's definition of "thick coat" is different which is where it makes it difficult to judge how much to spray.

Btw if you don't mind me asking, what is that bracket that sits behind the oil pump for? (gold one on the very bottom) I dont quite remember mine having something like that

I'm not sure mate what that bracket is. Could be a mount for the engine stand / crate box. I will ask my mech.

Has anyone tried this on their break calipers?? or do they get to hot to even both i know its only rated to 350 degree or something like that..

car wont be used for track work or anything either i think it would be a nice finish on them

any advice would be good

It can be applied to brake calipers as well. But this type of paint is only rated up to 117deg c (not 350 as that is in fahrenheit)

So the problem is that the paint would most likely flake away after some time as brakes generally get hotter than 117deg.

I would recommend painting it with higher temp paint I instead to make the effort worth while.

Edited by Ants
  • 2 years later...

Hi guys, while looking for some advice on wrinkle paint I came across your forum and in particular this post.

I have been trying to wrinkle paint my motorcycle exhaust silencers but so far I have only managed to get crappy patchy results. Some parts wrinkle nicely while others are flat. The main difference that I am doing from the advice here is I use no heat. I don't have a heat gun and because I live in England the temp is even colder than it is with you guys.

Could I carefully fit the silencers back on the bike while the paint is still wet and run the engine to cure the paint by heating from the inside out?

Would appreciate your help.

I've used it once and found that a thicker application will give you proper wrinkles. If you apply it like you would normal paint or primer, it will turn out flat. Don't remember the exact instructions but I think the second coat is meant to be quite thick

Doesn't matter what the ambient temperature is! That's what the heat gun is for...

Spray, heat evenly for a few minutes, spray, heat evenly for a few minutes, spray and then heat till it wrinkles up beautifully. Done.

That's all there is to it. Keep your paint thickness and heating method consistent and you'll pull off a nice finish every time. Too much paint (runs mainly) and you start getting getting inconsistencies in your wrinkles. Just a nice even coat each time and it'll come up nice.

Ive done my sons S2000 cam cover a few times in winkle finish, same results as above with the odd run down the side as per above.

My way is a little different, i preheat the gas barbecue (with lid) and place the item inside it to heat the paint.

Looking back your way may have been simpler.......might test it next time i do it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...