Jump to content
SAU Community

Recommended Posts

Looks awesome Glenn, glad to see you're getting stuck into it again!

I'll have to drop around for a look soon.

The Torana hatch is definitely a shape that can be made look very nice. Big arse flares are certainly a good start to that!

Started extending one of the front flares, thought I would try the tape and bog trick.

Cut the bottom off the flare and screwed both parts to the guard.

IMGP2976_resize_zpsl9i1vl9u.jpg

Put masking tape across the two.

IMGP2977_resize_zpsi4z87efj.jpg

Mixed up some bog and towelled over the tape and also cut some tig filler rod that I pushed into the bog to give it some extra support.

IMGP2978_resize_zps1jeezlhq.jpg

After the bog was dry I remover the flare and fibreglassed the inside.

IMGP2980_resize_zps8ymrjruz.jpg

Still needs a lot of work but should come up ok.

IMGP2982_resize_zpss96ilcfz.jpg

Got the other side flares done and put it on the ground to see how it looks.

This is with no springs sitting on the bump stops to check clearances.

IMGP3005_resize_zpsztdg0tji.jpg

IMGP3003_resize_zpssqvypsee.jpg

This is at standard ride height, will probably lower it about 20mm.

IMGP3000_resize_zpsknvqcp99.jpg

IMGP2999_resize_zpsq3o07h4m.jpg

  • Like 4

Decided to try and for Currie Enterprises Johnny Joints to the front caster rods since the rubbers are flogged out.

I think these will be ok considering they are used in the suspension of 3 ton rock crawlers and the engineer is happy with them because of the urethane bush.

It's a pity it wasn't 0.4mm bigger in diameter then it could have been pressed in and not have to weld it.

IMGP3014_zpsj5ga3ko3.jpg

IMGP3015_zpsnxaqh3e6.jpg

Tapped a new thread for the grease nipple through the castor rod and lined it up with the grease nipple hole in the johnny joint then welded it on both sides.

IMGP3016_zpsihofv541.jpg

Also dropped the motor, turbo and dump pipe back in to see if the brake line will clear and be far enough away from the exhaust.

IMGP3020_zpsrhey1dx5.jpg

  • Like 4
  • 2 weeks later...

Started filling in the gap from cutting the body to clear the tyres, because I've had to cut so high I had to weld the two inner panels together first.

The fun of welding through tar, body deadener and paint.

IMGP3035_resize_zpsmndikqmm.jpg

Little bit of rust in the lower 1/4 so easier to just cut the whole section out as this is covered by the flare.

IMGP3037_resize_zpsm701kxiz.jpg

One side done.

IMGP3039_resize_zps4d5hsqm0.jpg

I always liked the drop tank style look on the old SLR5000 Toranas.

If you wanted to keep that style, maybe you could speak to Julian at Aftermarket Industries about a fuel cell setup that replicates that and incorporates baffling and a surge tank internally.

He does amazing work and comes highly recommended for all sorts of fueling work.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...