Jump to content
SAU Community

Recommended Posts

genuine nissan HICAS tie rods (different to front tie rods!) are about 250$ for both. from nissan. not cheap. but if you go ling long...well...yeah

well if you got a GT-R I wouldn't use ling long, but I own a R33 GTS-t (ling long is acceptable) haha :)

^ maybe he likes HICAS :)

Theoretically it makes sense to have HICAS, and the system was revised in Series III GT-Rs like yours Paul, prior to that HICAS was pretty shit.

I've tossed mine in the bin too, but I own a fridge.

A lock bar doesn't really solve the problem that you probably have anyway. The outer tie rod ends are the spot that wears the most, and a HICAS delete bar leaves those in place. You'd still need to replace them.

Question.....does 5500 rpm relate to a particular road speed at all? HICAS is known to exhibit it's problems at particular speeds because the HICAS computer reaches "panic mode" at those points when given sensors are not working. Steering angle sensor is one that people often accidentally lose when they put a different steering wheel on the car and the hub doesn't have the drive pin for the steering sensor. On my car (last century) it would crank the steering wheel over to the (left? right?) by about 45° when over 80km/h just because no steering sensor. HICAS panic. No steering sensor also meant I couldn't put it into diagnostic mode which made it very hard to work out what was going wrong. The HICAS computer also looks at VSS, and for all I know in the later GTRs it might even be looking at the G sensors. There's lots of things that can make it act flaky.

Try to put it into diagnostics mode (no, I don't know how to do it on your car, only on an R32). Failing that, get a mechanic with a decent scan tool to hook up to the Consult port and see if there are any codes in the HICAS computer. You may have to take it for a drive and trigger the fault to see anything.

Try to put it into diagnostics mode (no, I don't know how to do it on your car, only on an R32). Failing that, get a mechanic with a decent scan tool to hook up to the Consult port and see if there are any codes in the HICAS computer. You may have to take it for a drive and trigger the fault to see anything.

yeah I'm thinking the same

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...