Jump to content
SAU Community

Recommended Posts

So, as the topic suggests, I recently had a 19 inch 265/30 tyre with approx 4000 km of driving suffer a collapsed inner sidewall. The manufacturer says it was due to under inflation. I normally run around 34psi and have been told it should be 40psi. I've run that pressure for years with no trouble. What do you guys reckon? Discuss..

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/
Share on other sites

I have always ran 32-34 psi in my tyres. Even on the track day I ran 32 psi to cope with the extra heat.If I put 40psi in tyres it seems to harsh of a ride. I've never had a blow out but I have seen tyres on other cars start to get big bubbles in the side wall before. I think it was a defect in the tyre that I saw.

I told one of the owners to take it back to where she got it from and they basically said the same thing it didn't have the right pressure.

It seems to be a cop out from the tyre retailers.

Is it possible to get a leak past the rim with hard take offs and cause the tyre to go down quick and blow it out?

Waits for derderpumkin to put his 1c worth into this thread.

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6891776
Share on other sites

34PSI sounds incredibly low to me - what you'd expect on a 185/60R14 or something.

When I get new tyres fitted, I always ask the staff what pressures to put in. Typically the lower the sidewall, the higher the pressures they're recommending. 40PSI sounds pretty normal for a 265/30 to me.

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6891783
Share on other sites

I have run same pressure on an 18 inch 265/40 on my old GTR for 6 years including 7 or 8 track days etc and never had any issue. If 40 psi is suggested and I run 34 that means its around 85% inflated. Is it reasonable to say that 15% under inflation will cause tyre failure??

I reckon thats a bit of a cop out. I was never instructed anything regarding pressure when getting these tyres. Surely they should come with a warning at point of purchase if this is so?

Anyway the tyre company has replaced the failed tyre but be careful guys!

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6892258
Share on other sites

The only time I've dropped the pressure to 34 was for a drag day once. Straight after that I've pump it back up to 38. I find 40 a bit too high personally and typically just run 38. 35-36 will give a slightly better grip but for daily driving 38 is good enough for me. 265/35/18 Michelin PS2.

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6893107
Share on other sites

I used to run 34psi in my 225;50;16 on my R32GTR but was told to low , told 40-44psi was better suited to my car .tyres were

K102 hankooks

Dunlop sp sport fast response

both above size and never had any problems like blow outs etc

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6894439
Share on other sites

I run a 235/45/17 and the tyre shop guys recommend it be on 34psi. I normally bump it up to about 38-40 as I find this is gives me a better ride. Never had any issues at all.

If the manufacturer is saying that the issue is caused by under inflation than to me that is a massive cop out.

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6894836
Share on other sites

I run a 235/45/17 and the tyre shop guys recommend it be on 34psi. I normally bump it up to about 38-40 as I find this is gives me a better ride. Never had any issues at all.

If the manufacturer is saying that the issue is caused by under inflation than to me that is a massive cop out.

That would be my thoughts.... Unless it was running 20-30psi or something way out of spec!

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6894841
Share on other sites

Interestingly when I checked my rear 265/35/18 tyre pressures at Caltex Bolivar on the way to Kadina they were 44psi - I even commented on this to others there. I had them fitted around 2 months ago and had not checked them since.

Bizarrely the front 235/45/18s that were fitted by the same shop at the same time were 28 and 32psi - weird.

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6896361
Share on other sites

yea i run the same as krishy. :action-smiley-069:

I run a 235/45/17 and the tyre shop guys recommend it be on 34psi. I normally bump it up to about 38-40 as I find this is gives me a better ride. Never had any issues at all.

If the manufacturer is saying that the issue is caused by under inflation than to me that is a massive cop out.

Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6896804
Share on other sites

I run around 40-42 psi on my 18s depending on how the tyre is wearing. I would class 34 as under inflated on a tyre with such a small sidewall. The smaller the sidewall the higher the pressure you need. Roughly speaking, if you have half the sidewall with the same amount of flex it will get twice as hot.

It is also a good idea to check your pressures regularly, particularly after you have new tyres fitted. You will find that in the first 500km or so they will drop pressure as they bed in. I have had tyres drop 10 psi in the first week and then not drop again for 10,000k

Edited by Race__24
Link to comment
https://www.sau.com.au/forums/topic/427051-tyre-pressure/#findComment-6897826
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...