Jump to content
SAU Community

98 Plus Octane Booster

MRHD66

By MRHD66,
in Engines & Forced Induction

 Share

Recommended Posts

Joshbigt62r Proficient

Joshbigt62r

Posted
Posted

You can get e85 delivered in drums but it's quite expensive isn't it compared to at the pump.? Better off going water methanol + 95-98 octane fuel preferably 98 octane and water/meth as jet_r31 mentioned.

Cheers Josh

XR Pilot Contributor

XR Pilot

Posted
Posted (edited)

I looked into this a fair few years ago before E85 was available - octane booster will generally raise a fuels given octane by a few points. Ie point-something of an octane. So 98 will become 98.2 octane for example. The only way to get a decent boost in octane is to mix something like Toluene with 98 (121RON, turbo F1 cars used an 86% Toluene/14% n-Heptane filler blend. It's pretty nasty to handle but you could get it in drums as of a few years ago). Mixed at 65% 98 / 35% Toluene this will get you up to around the same octane as E85 at a much higher cost vs pump E85.

I think your only viable options are either reduce the compression ratio of that motor to run 98, run water/meth like Darren said (if you do run water/meth I'd listen to this man!), buy E85 drums or take a trip to either Newcastle or Kempsey and fill up a few jerry cans.

Edited by XR Pilot
WMDC35 Experienced

WMDC35

Posted
Posted

Octane booster is also completely unreliable and probably doesn't even add half as much octane rating as claimed. I made some from mothballs and petrol in the 1990s that was probably at least as effective (ie it didn't really do anything).

mythbusters did a test with fuel additives, the moth balls seemed to do pretty well haha

JustinP Mentor

JustinP

Posted
Posted

I definitely would not recommend using 98 + octane booster. Due to some flooding that we had a few years ago, I got stranded in my R34 and was forced to use 91 RON fuel as it was the only option I had to get home. I added octane booster as a safeguard. Still suffered engine failure haha :P Thankfully I can laugh about it now! 3 years and counting and I still have not finished rebuilding it!

I would recommend the water / methanol option. But remember, as you are relying on it for everyday driving you need to make sure the setup is ultra reliable and has the appropriate failsafes.

Super Drager Mentor

Super Drager

Posted
Posted (edited)

I definitely would not recommend using 98 + octane booster. Due to some flooding that we had a few years ago, I got stranded in my R34 and was forced to use 91 RON fuel as it was the only option I had to get home. I added octane booster as a safeguard. Still suffered engine failure haha :P Thankfully I can laugh about it now! 3 years and counting and I still have not finished rebuilding it!

I would recommend the water / methanol option. But remember, as you are relying on it for everyday driving you need to make sure the setup is ultra reliable and has the appropriate failsafes.

Well that sounds wrong, if you weren't on boost and loading the car up it shouldn't matter. Baby the car and you can drive it on 91 octane easily. I've never seen a car so aggressively tuned on the low load part of the map that it detonates on 91 octane.

Edited by Super Drager

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Quieter performance exhausts (or muffler add-on options)

      By Murray_Calavera · Posted

      Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...