Jump to content
SAU Community

Cylinder Not Running On Idle? R32 Gtr

bilaldabab

By bilaldabab,
in General Maintenance

 Share

Recommended Posts

bilaldabab Contributor

bilaldabab

Posted
Posted

Hi Guys,

I have a problem at idle with my GTR, cylinder number 5 is not running when idleing or not under load, When the engine get some load, it kicks back in and runs fine with plenty of power. I have replaced all 6 spark plugs, i have swapped over the coil packs with others and its not a coil pack issue. However when i Unplug the plug to the 5th coilpack, the revs don't change/drop. So I'm guessing it has something to do with the plug/wiring?

Anyone got any advice before i start replacing everything?

I recently replaced the whole engine and got it tuned. This started happening a day after i got it tuned. Took it back to the mechanics who installed the motor and they couldnt find the problem...

Any help would be greatly appreciated!

GTRNUR Grand Master

GTRNUR

Posted
Posted

Swap your number 1 and 5 coil packs and see if the problem moves. If it does you know where your problem is.

Next, run the engine with the number 5 coil pack out of the head, and with a spare plug in it, sitting on top of the motor and watch for spark. If there is no spark, then its wiring or ignitor.

If there is spark you need to eliminate fuel. Swap the number 5 and 1 injectors and see if the problem moves. If it does, then injector. If not, then potentially wiring or ECU issue.

Borrow a stock /replacement ECU from someone and see how it goes. Have your tuned map uploaded if need be.

  • Like 1
DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Sounds like it could be a blown intake gasket on that cylinder. Get some brake cleaner or wd40 etc and while the car is idling spray around cylinder 5 inlet, throttle gasket and injector oring etc. see if the idle changes

bilaldabab Contributor

bilaldabab

Posted
  • Author
Posted

Swap your number 1 and 5 coil packs and see if the problem moves. If it does you know where your problem is.

Next, run the engine with the number 5 coil pack out of the head, and with a spare plug in it, sitting on top of the motor and watch for spark. If there is no spark, then its wiring or ignitor.

If there is spark you need to eliminate fuel. Swap the number 5 and 1 injectors and see if the problem moves. If it does, then injector. If not, then potentially wiring or ECU issue.

Borrow a stock /replacement ECU from someone and see how it goes. Have your tuned map uploaded if need be.

I have tried swapping my number 1 and number 5 coil packs and it made no change.

I will try the rest when I get a chance this week. Thanks for the info, will let you know how I go!!

bilaldabab Contributor

bilaldabab

Posted
  • Author
Posted

Sorry forgot to mention, also when its a cold start, the revs drop quite a bit and struggles to stay on (turns off most of the time), i need to keep my foot on the accelerator for about 15-20 seconds before it stays on..

bilaldabab Contributor

bilaldabab

Posted
  • Author
Posted

So i tried spraying some throttle body cleaner on the injectors earlier, the revs did not change on injectors 1, 2 and 3. however the revs went higher by 100-200 rpm.. when sprayed on injectors 4, 5 and 6.... when i sprayed it on all 3 at once, the revs jumped upto 500 rpm.

Does this mean the intake gasket is leaking towards the back? Could this be the issue or is this an entirely new issue?

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Yes sounds like the inlet gasket is blown. Its pretty common to happen as the gasket gets old. I normally replace the inlet and throttle gaskets with a set of metal nitto gaskets. Also check all the hoses under the plenum as they may need replacing while the plenum is out

SargeRX8 Grand Master

SargeRX8

Posted
Posted

Is that the gasket from runners to head? Shouldn't be hard. I think the rb25 plenum to runners is probably the ugliest job to do. I did it without a guide but there should be something readily available. Google change rb26 plenum gasket or intake gasket.

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Its a veryfun job to do on RB26's. willtake atkeast 3hours to get off, then cleaning of old gaskets and replacing hoses etc. then atleast 3hours to get back on.

DO NOT CLEAN IN AND AROUND THE THROTTLE BODY BUTTERFLIES!!!

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Yes I can see how that would put you off HFM, especially with the price of good quality brake fluid. From what I understand it as you say the BM50 is the standard BMC for a R32 GTR, I must admit I would like to go far a Genuine Nissan BM57, but lack of cash prevents that at present. With the price being so close between the genuine BM50 and BM57 a BM57 New it seems a better choice as you gain that 1/16 bore size with the BM57, I would be interested in how much difference you feel with the BM57 fitted. I am going to take SteveL's advice in the short term and see how much actually comes out of that proportioning valve vent and save up for the Genuine Nissan part. Thanks for clarifying the HFM failure
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      Thanks mate. I just got the post inspection 1/2 done from state roads when the starter motor packed up, either that or the car alarm system is having trouble.  OEM part number 23300-AA112.
    • oHBoy.
      Starter motor replacment teeth count.

      By oHBoy. · Posted

      Hi, I though I was coming to an end in finding a replacement starter motor for a rb25de neo. I came across a starter motor from Taarks and a message below stating: Direct fit. 11 Tooth count. All below part numbers have been superseded to 11 teeth. Can some body shed some light on going from 8 teeth to 11 teeth apart from 36-month / 25,000 km warranty for passenger vehicles to 12 Month Warranty. Compatible with the following Nissan part numbers: 23300-20P00 23300-20P01 23300-20P05 23300-20P10 23300-20P11 23300-AA111 23300-AA112 23300-AA300 23300-08U10 23300-08U11 23300-08U15  
    • niZmO_Man
      J50 clock date suddenly reset to January 1

      By niZmO_Man · Posted

      Low battery? Maybe check capacity? I know first-hand, on BMWs if your battery drops below 80% capacity, it starts causing strange issues.
    • niZmO_Man
      Wheel Sizes & Offsets For Skylines

      By niZmO_Man · Posted

      8.5 +37 = should fit rear, but I think it'll hit on front. What you want is low 30s/high 20's front, mid 30's rear. That 17" screenshot you posted looks good, I'd run it on my R32 (but that's long dead now). For tyre sizes, my rule of thumb is: 8': 235, 9": 255. But that's just my opinion. Nismo sizes: 18x8.5+35/18x9.5+38 is a good starting point.
×
×
  • Create New...