Jump to content
SAU Community

Recommended Posts

Got a mate's new 25/30 running today but the oil pressure seems to be a lot higher than it should. Was over 100psi at cold idle. It's currently got running in oil in the engine and has 2 x1.5mm oil restrictors to the head and I'm 99% certain a RB25 oil pump. The vct has an external feed to it but isn't wired up. I'm running a 25 pump on my RB30 and its only got around 60psi at cold idle. Is there any logical reason why it would be running such high pressure?

Also the vct feed is a -4 line. Does it need a restrictor in it at all or will it not matter as we most likely won't be wiring it up so the oil will just drain back to the sump

Edited by PSI086
Link to comment
https://www.sau.com.au/forums/topic/427432-rb2530-high-oil-pressure/
Share on other sites

The oil is a Penrite running in 20/50. Going to run a 10w in it once its got a few km's on it and is ready for synthetic though. Might just see what the pressure is like with the proper oil and normal running temperature. I can't see any reason why it would be higher than a normal RB25 as everything is identical besides the lack of oil squirters under the pistons

Just got the car running with the RB20 tune which was in it previously so can't really take advantage of the vct just yet. Will most likely wire it up though. From what I understand it just needs to be activated with an rpm triggered relay?

  • 7 months later...

sorry to bring up the dead guys but im going though the same drama at the moment with my rb25/30 non vct that's just being built and getting tuned

120psi on cold startup and idled at 1500 on penrite running in oil. this seems worrying!!!???? potential to blow seals etc?

im reading this from a auto meter prolite mechanical gauge.

not sure what the warm oil pressure will be just yet as I haven't let it get to that stage yet.

the oil pump is a rb25det pump with billet gears.

block has 2x 1.3mm restrictors and the vct line is disconnected.

ANY IDEAS ON A FIX??

oh shit! that's high for cold start!! once warm that aint to bad! wat oil ?

at what point do we start thinking f**k that's dangerous could blow rear main and front seals etc?

hasn't done any kms, 1st startup was today and after about 10seconds I noticed it was sitting on 120psi at 1500rpm (didn't wana rev any higher plus 1st EVER start up for the engine.

  • 3 months later...

hey all, find any solutions to these 25/30 high oil pressure issues??

my freshly built forged rb25/30 is showing over 100PSI on my autometer mechanical gauge, oil features include:

tomei oil pump

2X1/3mm restrictors

-12 rear head drain

2X-12 sump breathers

2X-12 cam cover breathers

grub screwed VCT feed in head

VCT sensor removed and capped

drilled out oil drains in block

2L accusump

5.5L sump

19row mocal cooler

GREX oil thermostat and oil filter relocation with ryco z145a filter

on penrite running in oil 15w40 it was showing high oil pressure over 100psi on cold start then down to 90 once warm. a tap of the revs to 2500rpm and it went to over 100psi again (gauge only goes to 100psi). after 250kms the oil was drained and a penrite 10w40racing synthetic was put in. once again on cold start over 100psi but once warm it dropped to 80/85psi or there abouts at idle and only went over 100 after 3000rpm

I was thinking of going a lighter viscosity maybe a 5w30synthetic or something? I only use penrite.

could anyone recommend anything?? or does anything look out of place? im a little worried.

I think im going to get a larger scale mechanical gauge to see where there press really sits after 100psi..

I previously had a rb25 pump with billet gears and was showing the same signs

any help would be HUUUUUGELY appreciated im really stumped and worried.

Cheers

Corey

Edited by ScreamerNewbie

If your bearings clearances are all standard then use a standard viscosity oil which I think is a 30 weight?

If you cant get the pressure to drop when warm below say 120psi at full noise where the oil relief is cracked open then you will need to reduce the spring pressure in the bypass of the pump. If you don't want to do that then you can hook up an external Peterson oil pressure regulator between your sandwich plate and oil cooler/filter arrangement and plumb that in so you can regulate the pressure going into the main oil gallery.

  • 3 years later...
On 10/15/2017 at 10:38 PM, pet vl said:

And iam still haveing trouble any idears its my car looking i to changing the spring in the pump HELP

Be more specific...what is your problem? What is the cold oil pressure and how long does it take to drop to say 100 psi?

I see your other post - just post in one place!

See what happens when you compare the spring pressures.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...