Jump to content
SAU Community

Recommended Posts

I would say, on the basis that the tests you have done so far are likely to give the highest possible fuel pressure you will ever see (cold weather, cold fuel, brand new pump) that you could get away with setting it just barely higher than it runs naturally. So maybe 63 or 64 psi. I would say that you are dead unlikely to get any more than you already are, and even if you did it would only be 1 or 2 psi, which would hardly ruin anything for you (richer is safer anyway).

As long as the reg and the fuel pump can keep that pressure stable across your whole operating range you should be gold.

As to your question about whether the loop you have in your line is causing any restriction....I would suggest not. Unless the hose is quite severely closed down it will still not have anywhere near as much restriction as the reg itself.

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

.... wait for it.

My bet is that you have an air bubble between the fuel an gauge. Due to the orientation of your gauge.

Cheers

Justin

Which has only manifested itself as an issue now, after installing a bigger fuel pump? After running without issue for over a year on the old pump setup?

Air is more compressable then fluid, and would make the gauge read lower if anything. So that is not the problem

So restriction or FPR issue I say. I would pull the FPR off and just have a look at the ports and everything just in case theres something silly going on there

Might have found the issue! Pulled the regulator off last night and had a look at it, but couldn't see anything out of the ordinary. So then I had a look at the piece of return line that came off the regulator and looped around the fuel filter and spotted this:

431226_10151483541942541_708608272_n.jpg

There's some sort of restrictor in there. Makes me wonder where this hose came from, I never purchased any hose with a restrictor in it. In fact from memory I actually just reused the standard return line, though surely they don't have a restrictor in there? Amazes me that it didn't cause any problems until now. Anyway, haven't had a chance to check whether I can lower the fuel pressure now, will finish installing the ethanol sensor and put it all back together and report back!

Yeh, me too... Wondering if maybe this caused some of my power issues, but I don't think so. Tuners never mentioned fuel was a problem, and it wouldn't have affected response anyway. In any case, I'm sure it wasn't doing any good, so I'm glad to be rid of it!

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...