Jump to content
SAU Community

Recommended Posts

Hey all :)

I have a problem with my skyline. Only occasionally I will start it and begin to drive.. then when I'm accelerating it seems to lose power and slightly "bunny hop" the bunny hops are not aggressive. it just doesn't seem to be able to get to higher revs. It does happen when it's cold but by the time it's warmed up it still has the problem.as I said it only does it every now and again. Does anyone have any idea what could be wrong?

Link to comment
https://www.sau.com.au/forums/topic/428944-intermittent-problem-with-r32-gtst/
Share on other sites

No mods except for a coke can in the blow off valve (bought like that) :P

Don't know the service history from previous owner. Has had a complete full service. Was happening before I recently got it serviced.. mechanic changed the fuel filter and spark plugs (thinking they were the cause) but problem still persists

It happens at any revs. It happens whenever I accelerate

  • 1 year later...

Found this thread and am bumping it because I have a similar problem. I'll describe it in more detail though.

This happens occasionally, and only early in any drive if it does. Not like right out of my garage but 1 or 2 minutes in. I will probably happen at a frequency of about once every 3 times i drive the car.

Once it happens it will happen until i let it sit out of boost for a while and it will be ok. I even did 5 runs at autocross after this, problem did not crop up.

How violent it is depends on how much throttle i'm using. If I hold it down as i'm trying to accelerate and not let it if it reminds me as if someone who is just learning to driving a manual is driving the car. Off-boost it doesn't do this. It only does it at RPMs in which the turbo is building or holding pressure.

Same recommendations? I don't have another AFM to try otherwise I would but I could install my powerfc and put in a Z32 AFM.

I had an r32 gtst back in 2004 which would do that, the car would lurch back and forth violently under acceleration. Turned out to be a really dirty fuel filter, wasn't allowing sufficient fuel to the rail so the car was suffering fuel starvation. Upon reflection I'm surprised I didn't destroy the engine, must have been running ultra lean during those periods.

I had an r32 gtst back in 2004 which would do that, the car would lurch back and forth violently under acceleration. Turned out to be a really dirty fuel filter, wasn't allowing sufficient fuel to the rail so the car was suffering fuel starvation. Upon reflection I'm surprised I didn't destroy the engine, must have been running ultra lean during those periods.

Did it do this all the time or only occasionally like it's doing for me?

I would think if it were a fuel filter it wouldn't just stop and be fine for hours.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...