Jump to content
SAU Community

Recommended Posts

Hey guys,

I must say I'm a tad nervous, I bought myself an R33 GTR some time ago (6 ish months) from Tassie and got it shipped to QLD. I'm about to get myself a road worthy certificate so I can register it in QLD. Just wondering if any guys had much trouble getting a RWC for their skyline? What does it involve? What precautions should I take?

Mods included with my skyline are:

Coilovers

turbo timer

boost controller

sound system

cat back exhaust

pod filters

coil packs

The car is in fantastic condition, no signs of rust (that i'm aware of) I know there is an exhaust leak at the dump pipe which I plan to fix next weekend assuming the weather holds. I'm wondering how anal the guys will be when they carry out the inspection. I plan to revert to the pod filter back to stock and remove the amplifier. But what about the boost controller, turbo timer and coil overs? Do I need to remove and revert the coilovers?

I apologize for coming off as dumb. Being a former Tassie fellow, you just take your POS in and bam, you got the tick of approval. I hear QLD is a little more strict than that lol!

I have read the forms and done some research but really can't get any specifics. Any help, guidance would be fantastic! Thank you in advance :)

Hide what you can, secure what you can

Take it in and ask they not stop at noise and ride height. (90db @3000RPM, 100mm clearance from front to rear)

Shops hear you drive in and say too low/too loud for starters.

Realistically from what you have posted.

- Coil overs - adjustable ??

- turbo timer (hide)

- boost controller (hide)

- Pod filters (secured/coverd)

- Exhaust -

Plus any other defect items as per regs

I think it's best to find the fail points and target your effort and dollars.

Trying to second guess will get you so far, may get you over the line, won't stop you from being defected tho.

It depends on the workshop you take it to. Some will be more picky than others. Provided there aren't major oil leaks, things like brake pads and tyres are in good condition, and nothing stands out as being obviously dodgy then you shouldn't have to many problems. Wind your coilovers up to a reasonable height and turn your turbo timer off and pull the boost controller out to help things along as well.

And finally, don't go in looking like a douche. For example, if you wear a flat brim cap at an angle, perhaps leave that at home.

Hey thanks for the heads up guys, I work so I'm always "suited up" during the week so presenting myself won't be an issue at least. Coil overs are adjustable and wound up to a nice height (coke can fits under nicely) with some head room so that won't be an issue. Car doesn't present any leakage issues, brakes and pads are fine too. Car is just stock and the last major service (few months ago) fixed those little things. Sounds like I know what has to be done! Thanks for your input :)

A rwc in qld for an imported car entailes a small bottle of lubricant, a thick rubber glove, approx 2kg of uniodised rock salt and the tears of a thousand baby fur seals.

Edited by 33GTRV
  • Like 1
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...