Jump to content
SAU Community

Recommended Posts

Hey SAU,

what sort of power can you get untill stock internals need to be modified on rb25det? Only reason i'm asking is my setup upopened would get me around 270-300kw on pump fuel, but i'm going e85/flex fuel now and that will give it more power and yeah just want to know.

cheers

Link to comment
https://www.sau.com.au/forums/topic/429022-rb25det-how-safe-are-internals/
Share on other sites

Depends which RB25 and what supporting mods etc... Condition of the engine? How it's been treated? Intended use...

Go find the 300kw+ unopened thread which will answer all your questions and allow this Thread to be locked.

how much hard mileage has it done so far?

Mine? About 9000km... Including a close call with a lean out and also overheat (Haltech ECU protect stepped in luckily).

Well here's my setup

Garrett 3076r .82 rear housing

6boost manifold

50mm turbosmart wastegate

Front facing plenum

90mm tb

Sard 850cc injectors

450lph e85 pump -will have surge tank

Link g4 plug and play

Engine done about 120ks easy life, only reason I asked as I was going to use pump fuel but now going flex fuel/e85 and I will gain kw and will have over 300kw on a max of 17psi and wanted opinions on how long internals will last

I had a similar setup and maxed the turbo out... At that stage my engine had done 140000km and has had a rough life... Ran it on 360kw where it was thrashed...

It now has the HTA turbo running 390ish and has 149000km...

It's all in the tune! There is no magic number that will make your engine safe.

How much of a gain did you did from flex fuel? Okay hopefully when it gets tuned it's done right

About 30kw on low boost... We didn't tune pump 98 fuel on high boost though so no full boost comparison. But it's nice and responsive on ethanol, smells good too ;)

350 is about the safe limit, we have a few in the 400's but i would not recommend it.

on a R33 motor right? don't the ringlands let go? I know R34 RB25DET NEOs are built as well as tanks

Hey man to be honest ill tell you a little trick water meth injection if u can do that u can push it further on stock internals

Lolololol..... So you are trying to tell us you can increase the strength of the engine internals? You sir are brilliant!

No I'm saying you can push the internals a little further with water meth injection like less chance of detonation at higher boost.

You can do that with E85 too, its not new and its not a secret!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...