Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

with my boost controller switched off, it will run the minimum the wastegate spring/preload allows, so long as there is no damage to the wastegate lines.

that would be consistent with wastegate functioning correctly :) What pressure wastegate spring limits your boost?

I have often wondered about Wastegate actuation, as over time vacuum drops in an engine and the wastegate seals wear. So unless you constantly adjust it the boost control will lessen over time - good reason not to buy used wastegates.

On a far less serious note, and in response to 2.1 bar boost. In a modified GTIR years ago a friend used to boast that his engine could handle anything failing, so another friend told him to disable all boost control (wastegate locked) and remove the knock sensor for a 10 second full throttle blast. The thing went like a rocket - didn't blow up then, but one week later he called for a tow as he had just played catch the conrod. Motor pulled down and bearings were mushroomed and block had an awesome porthole. :)

lol......epic fail to that Gtir.

Having said that 2.1bar is no laughing matter

Yep, he was initially really happy about proving the doubters wrong until the engine died.

2.1 is high. I remember years ago hearing that Rigoli was ordering 5 bar map sensors, as the 3 bar were out of range on the racecar.

yeah those Rigoli boyz were truly nutz!

I remember their 4WD Hyundai Accent which ran 10secs or less

Waz crazy what they did by transplanting an Evo drivetrain in that chassis........but it worked!

yeah those Rigoli boyz were truly nutz!

I remember their 4WD Hyundai Accent which ran 10secs or less

Waz crazy what they did by transplanting an Evo drivetrain in that chassis........but it worked!

That was the exact car - good memory :) the rumour was 43psi. I think it had a T60 or T70 Turbonetics custom turbo from memory.

See this thread for fond memories - 9.4sec 1/4. http://www.skylinesaustralia.com/forums/topic/26511-rigoli-accent-in-the-9s/

Yep. Good times mate.......good memories.

I also happened to own an accent att when they did that lol

Turbonetics rings the bell as well.

Pretty sure I have a FastFour Mag somewhere about it

that would be consistent with wastegate functioning correctly :) What pressure wastegate spring limits your boost?

1.7 bar spring, lots of preload, did a few more tests consistent 2.08 - 2.1 bar, so needs to be backed off a tad.

That was the exact car - good memory :) the rumour was 43psi. I think it had a T60 or T70 Turbonetics custom turbo from memory.

See this thread for fond memories - 9.4sec 1/4. http://www.skylinesaustralia.com/forums/topic/26511-rigoli-accent-in-the-9s/

there is a black evo 5 thats running 501kw @ 43psi, its currently on the market for 30k

and shipping? Happ are in brisbane. Ramps already here

morning Tony

Edited by MagicMikeZ32

1.7 bar spring, lots of preload, did a few more tests consistent 2.08 - 2.1 bar, so needs to be backed off a tad.

so wastegate spring 1.7, no boost control gives 2bar? Boost creep?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I think he was only proposing to use the wire, not the sender. Simply because it runs from the right place to the right place. Personally, I wouldn't hack up the factory wiring like that. I'd just lay in the Defi loom.
    • From memory it wasn't too hard to simply see which wire ran where when you plug that in. Unfortunately also from memory the OEM sender does not use the same configuration 99.9% of gauges run. So in other words if you connect the signal wire that was running to the OEM gauge to your DEFI gauge you might find your oil reads at 200C or some other incorrect value. I remember having the same line of thought and then running new wires/senders to match the gauges I have. The pinout is available in the R34 workshop manual.
    • Does anyone on here know which wire on the GTT triple gauge pod harness is for the oil temp gauge? my sensor works fine but I upgraded the gauges to DEFI advance. And if I can simply piggyback off the oem oil temp wire to the Defi oil temp sensor wire that would make life so much easier. 
    • Even face her a wash now that’s it worth more than my house
    • This was what I was invisioning, or Pete cutting a beer can up and hose clamping it around the catch can! Ha ha ha
×
×
  • Create New...