Jump to content
SAU Community

Recommended Posts

Today i took some time, Gave the old girl and oil and filter change and also installed the battery cover over the power steering section. Think it looks alot more neat now. Also yesterday i picked up my sticker bomb roof wrap. Hopefully have that put on during the week and ill post some photos up :)

1609870_10152218306247697_1972949727_n_z

1604872_10152215700297697_833494373_n_zp

  • 2 weeks later...

do you have a pic rudi of yours as I was looking at gloss black

Yes i do josh. i think i posted it last year on what have done to your stagea, other wise i;ll take another shot and post it or pm your mobile number and i;ll send it to your phone :action-smiley-069:

Yes i do josh. i think i posted it last year on what have done to your stagea, other wise i;ll take another shot and post it or pm your mobile number and i;ll send it to your phone :action-smiley-069:

ist under black roof. in what have done to your stagea, and you comented on it

  • 1 month later...

car looks good. looking forward to checking it out on AJP, hope your package arrives in time

i shall be there!

look what arrived today! Just in time, pitty one wheel is damaged but i have been given a refund of $150 to get it repaired which i am pretty happy about. Were still not sure why WORK wheels would send out a damaged wheel. anyways pictures bellow!

wheels_zpsbde768ea.jpg

damagedwheel_zpsedbe0933.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...