Jump to content
SAU Community

Turbo Questions And Help.

Pure_Sincerity

By Pure_Sincerity,
in Engines & Forced Induction

 Share

Recommended Posts

Pure_Sincerity Enthusiast

Pure_Sincerity

Posted
Posted

I'm about to boost my n/a 34. Intercooler etc is sorted and fab work.

Q1. Do rb25 turbos and rb20 turbos use the same oil lines ? Because I have a set of speedflow braided oil feed and return lines an I want to know if they will bolt straight into rb25 turbos.

Q2. How would an rb20/25 turbo go if I get it rebuilt with a billet wheel and high flowed with a kinugawa adj actuator ?

Q3. Cost vs cost, which is better ? ^ that or going straight out and buying a kinugawa TD06 20G ?

The plan is to only run around 10psi as the n/a motors have higher compression values then the 25det neos. To pair with this, I'm just going to run the factory low mount manifold with a 2.5" twin entry dump, greddy type FV BOV and drift boost tee.

What's my best option ? Cheers guys. Kinugawa TD06 or rebuilt rb20 or 25 turbo with billet wheel and kinugawa actuator ?

Link to comment
https://www.sau.com.au/forums/topic/433613-turbo-questions-and-help/
Share on other sites
Pure_Sincerity Enthusiast

Pure_Sincerity

Posted
  • Author
Posted

Not much. Picked up a GREDDY FV BOV, permaseal gaskets, factory turbo manifold, twin entry dump and boost tee for $180 and I already had speedflow braided oil feed and return lines.

Looking at $400 for a return flow cooler with piping, $1k for a nistune install and tune then I'm looking for an op6 turbo or something similar.

  • 3 weeks later...
Blackkers Experienced

Blackkers

Posted
Posted

Not much. Picked up a GREDDY FV BOV, permaseal gaskets, factory turbo manifold, twin entry dump and boost tee for $180 and I already had speedflow braided oil feed and return lines.

Looking at $400 for a return flow cooler with piping, $1k for a nistune install and tune then I'm looking for an op6 turbo or something similar.

You running factory non-det injectors and fuel pump?

If you're buying injectors and a fuel pump I'd sugest going straight for E85. its perfect for the higher comp motor and you will make more power on that small turbo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...