Jump to content
SAU Community

Mt Cotton Hill Climbs / Motorkhana's

poohkies

By poohkies,
in Queensland

 Share

Recommended Posts

maclarenf1 Experienced

maclarenf1

Posted
Posted

look at the MG club page. all the info you need.

out of interest. are these open to anyone with any type of car. can a newbie simply participate with little or no experience, etc

cost - etc.

  • Like 1
defari Grand Master

defari

Posted
Posted

out of interest. are these open to anyone with any type of car. can a newbie simply participate with little or no experience, etc

cost - etc.

Short answer... No. You need to meet certain requirements etc. you can't just rock up in a hoopty leaking oil, bald tyres etc and expect to be allowed to drive

Melly Grand Master

Melly

Posted
Posted
HSCCQ run a bunch of Motorkhanas and Khanacross, they run the majority I know of up here and they also ran the 2012 Motorkhana Nationals so check them out if you want to do them.

Don't know about the MG club up here but in ACT the MG club ran the Motorkhanas not hill climbs and anyone was welcome as long as they had a CAMS licence. Hill Climbs down there were run by SDMA and again anyone was welcome...

Melly Grand Master

Melly

Posted
Posted

what's the HSCCQ i've got my cams level 2 licence from doing motorkhana's up in darwin

It's the club that runs them, pop it into google and it will come up :) Holden Sporting Car Club of Queensland but they aren't car specific it's just that the club started as holden and grew from there.

sneakey pete Grand Master

sneakey pete

Posted
Posted

One of the guys has a tow car that's a Holden, i think.

I used to do a fair few of these with those guys with my dad, haven't gone to one for a few years but he still does. they're a good bit of fun.

  • Like 1
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...