Jump to content
SAU Community

Recommended Posts

May take you up on that Mitch. Base on the youtube vids I've seen and the documentation it looks pretty straight forward. I'm just making up the external map and wideband interface looms now.

I can't imagine Haltech would have left any surprises for me. Out of the box it should control the fuel pump speed and send the correct TPS signals to the Attessa right? Ive seen lots of other people have issues with these two simple things... Edit: Other ecu's of course... Wolf/vipec etc...

Edited by GTRNUR

High/low fuel pump control is hard set at 5% throttle opening (from memory). The TPS follower for the ATTESA 100% works as per factory, as does the injection duty signal to the MFD.

The pre-loaded base map should be enough for you to get started with. Just make sure you load the calibration for your MAP sensor, set your TPS limits, enter your injector characteristics and deadtimes and away you go. Set base timing (i like to lock the CAS all the way clockwise) by enabling the ignition lock and adjusting the trigger angle. Dont forget to set the engine capacity, and if you're running an ethanol blend of fuel without a flex sensor, deduct ~33% from your injection flow rate to allow for the fuel density difference. :cheers:

Not necessary, it just connects to Inj1. The MFD does the rest.

If you were able to program up an 7th injector channel, it would need to be configured to have the same output pulse width as all the other injectors. Also, you would need to put a load on the output, or a pull up resistor to +12v so the MFD would be able to read the variable PWM square wave.

Sorry no dyno time yet.

The Haltech is in now. It idles and revs. Didn't get a chance to drive it anywhere though, nor do anything but do the basic setup on the weekend.

With any luck I can take a day or two off later this week and spend some time on the phone with Mitch.

AI tell me my surge tank is still 2+ weeks away as well.

  • 2 months later...

More changes are still in the works. I've replaced the entire fuel system again after being talked into going down the E85 flex fuel path. So bigger injectors, more pumps, bigger fuel lines, external surge tank and bags of fittings...

It takes for ever to get parts up here too. Pay for overnight and it arrives 3+ days later.

I've yet to source and wire in a flex fuel sensor, and I've got locate a fuel cooler to mount behind the diff too.

The interesting news is that I hope to be getting Mercury Motorsports to come to Cairns to do the final tune and setup of the car. If anyone can get it to produce a good final result, I think they are certainly capable of it.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
    • There is a warning that "this thread is super old" but they ignore that anyway...
    • With 10% Ethanol, we're talking 2-3% fuel consumption difference. The emissions reductions and octane boost in my opinion far outweigh this almost non existent loss.    My tanks sitting at 80%. Luckily that should go down fast as I'm on vacation again for the next two weeks. 
×
×
  • Create New...