Jump to content
SAU Community

Recommended Posts

My rb25 is blowing a fair amount of blue smoke under hard acceleration. I did a compression test and it came up 160 across all 6. There is no smoke on idle or slight revving only when I give it a good rev. I replaced the turbo with a brand new one and the return doesn't seem clogged or anything. Has all brand new feed and returns. Also I don't have a down pipe on it at the moment and it doesn't make full boost until about 5500 or so on a t04e. The blow off valve doesn't go off and there is no sound of releasing pressure when off the throttle. All cooler pipes are tight. What would be the cause of excessive blue smoke?

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/
Share on other sites

it has a brand new turbo on it with 1.2mm restricter, what are the signs of bad valve stems? ill give it a boot full and it will blow a shitload of blue smoke on hard acceleration, but if i keep boosting it the smoke gradually gets less and less, so pretty much the more i flog it the less it smokes so to speak (no i dont flog it all the time lol)

which leads me to believe its valves as theres no time for vacuum to draw oil through the seals.... but theres no smoke on start up or just putting around under say 3.5k rpm

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7101937
Share on other sites

I have had to install two 0.9mm restrictors to some Garretts just to stop the oil pumping out of the seals, you can tell as the oil is unburnt in the dump. If it is burning it, it is most likely internal, but check the intake for oil first, it could be the compressor seal or just leftover oil from the last turbo failure...

T04e is a pretty big turbo, I hope you haven't done the ring lands from booting it without tuning first. It will also be more responsive once it's tuned properly.

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7102089
Share on other sites

As stated above, potentially the oil control rings. Possibly also valve stem seals - will a leakdown test return poor figures if valve stem seals are shot? Or would they not allow enough air past?

Your other symptoms like the BOV are almost certainly unrelated :)

I'd start at the beginning of the system (filter and intake pipe - rocker breather return) and work your way to the exhaust. You've ruled turbo seals out (well, you haven't - but would be f**king horrible bad luck if you had 2 buggered turbos :P), so that leaves you with the rocker cover breather return, valve stem seals, and oil control rings to point at.

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7102998
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...