Jump to content
SAU Community

Recommended Posts

BC for sure, I had them in my last R34 & put them in my current R34. Went standard 8/6 & on full soft I dont think they are much stiffer than the king springs that were on before. Full hard really is HARD!

It's not listed as a Type 1 Hooning Offence AFAIK / IIRC so it wouldn't result in an impound..although, for the paranoids:

"Dangerous operation of a motor vehicle" is a Type 1 Offence...and a very broad offence at that...open to interpretation whether an excessively low car qualifies....:P

You'd have to be pretty unlucky to get done for something like that...

Edited by fusion07

Cheers mate, does anyone know if your car is below 100m and your just randomly Encountered by police can they impound your car or is it just warning/defect?

AFAIK defect. Adjustable height coilovers are also defectable even if you are above 100mm. 100mm is whilst the car is under full load.

I have lowered my car leaving a finger width gap between the tyre & wheel arch & the body is still well over 100mm off the ground, I think it was around 150mm. I dont have a body kit on it.

My exhaust however at its lowest point is less than 100mm off the ground. Still not sure if they measure from the lowest part of the car or from a structural part.

I have lowered my car leaving a finger width gap between the tyre & wheel arch & the body is still well over 100mm off the ground, I think it was around 150mm. I dont have a body kit on it.

My exhaust however at its lowest point is less than 100mm off the ground. Still not sure if they measure from the lowest part of the car or from a structural part.

Lowest point mate. Get a bracket made to bring it up?

  • Like 1

Iirc the height adjustment threading can be spoiled/locked so it's impossible to go below 100mm, then mod plate issued. Most people wouldn't dare to spoil their expensive coilovers though so no one does it. I've been driving with bcs for 4 years now, only got pulled up once and the dude just said it's too low and drove off, mind you this is in an s15 that was slammed to kingdom come lol. My current caris much mmore sensibly set up and no attention attracted so far. If you don't plan to slam it then good chance they won't care, but it's your choice in the end.

Edit: left out an important detail never been through a roadside defect station ever. If you got stopped at one then that would be a different ballgame...

Edited by fusion07

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...